manualshive.com logo in svg

Tomy FLS-1000, Руководство оператора

Поделиться
Скачать
Tomy FLS-1000 Скачать руководство пользователя страница 40

ー 39 ー

 

5-11.  Draining the Sterilizing Water from the Chamber

CAUTION

Allow sterilizing water to cool down sufficiently before draining water 

from the chamber.

●

Water in the chamber or the exhaust tank may be very hot after the operation, 

causing burns.

①

 

②

③

④

⑤

⑥

⑦

⑧

⑨

LO W E R

U P P E R

Open the chamber lid.

Open the drain access cover.

Pull out the drain hose.

Place the drain container underneath the drain hose.

Open the drain cock by rotating it slowly and drain the 

sterilizing water from the drain port. If the water drains very 

slow or does not drain, the port may be clogged. Clean the drain 

port with tools such as a wire to remove the clog.

After completely draining water from the chamber, close the 

drain cock.

Place the drain hose back to its original position.

Close the drain access cover.

Close the chamber lid.

Open

Close

WARNING

Do not attempt to open the drain cock unless the pressure gauge reads 

0MPa.

●

If the drain cock is opened when pressure still remains in the chamber, hot 

water may spurt out, causing death, injury or serious accident.

Содержание FLS-1000

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды