Tomy FLS-1000 Скачать руководство пользователя страница 38

Страница: 38 / 64

ー 37 ー

※

If a system error or a power failure occurs during the operation, the autoclave does not flash or

light the COMPLETED indicator by deciding it as being an abnormal state. It does not flash or light

the COMPLETED indicator when the operation is temporarily suspended by pressing the stop key

during the operation.

※

If the autoclave detects an error in the system, a power failure, or temporarily suspension of the

operation, it will show an error code in the temperature display, or turn on the POWER FAILURE

indicator or the stop indicator.

Process status

“IN PROGRESS”

indicator

Operation completed

“COMPLETED”

indicator

Lid interlocked

indicator

Buzzer

Preparation completed

Off

Operation started

↓

One beep

Temperature rising process

Yellow on

Off

One beep

Temperature and pressure

rising process

Red on

Off

Sterilization process

Red on

Off

Temperature and pressure

falling process

Red on

Off

3 beeps

Temperature falling process

Yellow on

Off

Lid interlock release

temperature reached

(Operation completed)

Yellow on

Flashes

（

normal

）

Off

（

abnormal

）

Off

6 beeps

60℃ reached

Off

（

normal

）

Off

（

abnormal

）

Off

10 beeps

Table. Operation of the indicator and buzzer in each process of the sterilization cycle

5-9. Ending Operation

When the chamber temperature reaches the lid interlock release temperature, the sterilization

cycle is completed and the lid can be opened. Do not attempt to open the lid unless the chamber

temperature drops to 60℃. Otherwise, explosive boiling of water may occur immediately or

shortly after the operation, causing burns.

When the operation ends, the IN PROGRESS

indicator turns off. If the sterilization process is

performed successfully according to the set program,

the COMPLETED indicator will flash or turn on

after the operation is completed. For operation

of the indicator and buzzer in each process of the

sterilization cycle, refer to the table shown previously.

①

STOP

MEMORY

STERILIZE

LIQUID

START

FUNCTION

CHECK

TIMER

EXT.

SENSOR

COOLING

FAN

EXHAUST SPEED

FAST

TIME

TEMPERATURE

TIMER

COMPLETED

STERILIZE

LID

WATER

DRAIN

COVER

CHANGE WATER

°C

SLOW

STERILIZE

IN PROGRESS

Содержание FLS-1000

































































Результаты поиска

Содержание FLS-1000

Отзывы:

Бренды по названию

Популярные бренды

Tomy FLS-1000, Руководство оператора

Результаты поиска

Содержание FLS-1000

Отзывы:

Бренды по названию

Популярные бренды