Tomy FLS-1000 Скачать руководство пользователя страница 30

Страница: 30 / 64

ー 29 ー

Check that the water inside the exhaust tank is cooled down.

Open the drain access cover.

Remove the cap on the end of the drain hose.

Place the drain container on the floor and insert the free end of the drain hose into the

container. The water will drain when the end of the hose is lower than the water level in the

exhaust tank.

When the water level drops to an appropriate level, lift up the end of the hose.

Install the cap onto the end of the hose.

Insert the drain hose into the space on the left side of the exhaust tank.

Close the drain access cover. Check the drain access cover open indicator turns off.

To drain water from the exhaust tank

①

②

③

④

⑤

⑥

⑦

⑧

Check that the water inside the exhaust tank is cooled down.

Open the drain access cover.

Remove the exhaust tank cap.

Pour water in the exhaust tank through the feed-water inlet until the water level exceeds the

minimum water level.

Install the exhaust tank cap.

Close the drain access cover. Check the drain access cover open indicator turns off.

To pour water into the exhaust tank

①

②

③

④

⑤

⑥

LO W E R

U P P E R

Содержание FLS-1000

































































Результаты поиска

Содержание FLS-1000

Отзывы:

Бренды по названию

Популярные бренды

Tomy FLS-1000, Руководство оператора

Результаты поиска

Содержание FLS-1000

Отзывы:

Бренды по названию

Популярные бренды