Tomy FLS-1000 Скачать руководство пользователя страница 49

Страница: 49 / 64

ー 48 ー

When the sterilizing water change indicator is on

Drain water from the chamber and pour water into the chamber.

※

Refer to “5-11. Draining the Sterilizing Water from the Chamber”.

Press and hold down the CHECK key.

The buzzer will sound in approximately two seconds and the number of the operated cycles

after change will be reset.

※

To continue operation without pouring water into the chamber, press the CHECK key. Five

cycles can be performed.

①

②

6-10. Sterilizing Water Change Alert Function

When the set number of sterilization cycles is reached, the sterilizing water change indicator

lights up to notify the operator of the timing for water change to prevent the chamber from

getting rust by contaminated water inside. When the sterilizing water change indicator is

turned on, follow the instructions below for pouring water into the chamber. If the start key

is pressed without changing water while the sterilizing water change indicator is on, “A01”

appears in the time display and the autoclave enters into the standby mode. The number of

cycles which activates the water change alert function can be changed depending on the level of

contamination in water.

To set the change alert

STOP

MEMORY

STERILIZE

LIQUID

START

FUNCTION

CHECK

TIMER

EXT.

SENSOR

COOLING

FAN

EXHAUST SPEED

FAST

TIME

TEMPERATURE

TIMER

READY

STERILIZE

LID

WATER

DRAIN

COVER

CHANGE WATER

°C

SLOW

STERILIZE

IN PROGRESS

Press the FUNCTION key while the IN PROGRESS

indicator is off. The time display flashes “F00”.

Press the time setting up and down arrow keys to

show “F12” in the time display. The temperature

display shows the number of cycles which activates

the alert function when it is reached.

Press the START key. The temperature display

starts to flash.

Press the temperature setting up and down arrow keys to show the desired number of cycles.

※

The factory default value is 40.

※

The setting range is between 5 and 80 cycles. When “− −” is selected, the alert function will not

activate.

Press and hold down the START key to finalize the setting.

The buzzer will sound in approximately 4 seconds and the display will return to normal

display.

①

②

③

④

⑤

STOP

MEMORY

STERILIZE

LIQUID

START

FUNCTION

CHECK

TIMER

EXT.

SENSOR

COOLING

FAN

EXHAUST SPEED

FAST

TIME

TEMPERATURE

TIMER

READY

STERILIZE

LID

WATER

DRAIN

COVER

CHANGE WATER

°C

SLOW

STERILIZE

IN PROGRESS

Содержание FLS-1000

































































Результаты поиска

Содержание FLS-1000

Отзывы:

Похожие инструкции для FLS-1000

Бренды по названию

Популярные бренды

Tomy FLS-1000, Руководство оператора

Результаты поиска

Содержание FLS-1000

Отзывы:

Похожие инструкции для FLS-1000

Бренды по названию

Популярные бренды