Tomy FLS-1000 Скачать руководство пользователя страница 58

Страница: 58 / 64

ー 57 ー

Error code

Possible cause

Remedy

E20

The pressure inside the chamber is high

when the power is turned on.

※

It exceeds 5.6kPa.

Wait until the chamber pressure drops to 0MPa

and then turn on the power.

E22

The chamber pressure rises because the

shape of the article to be sterilized serves to

prevent air from escaping.

※

The pressure exceeds the value predicted

by the chamber temperature by equal to

or greater than 25kPa during full opening

of the valve.

Turn off the power switch and wait until the

chamber pressure becomes 0MPa to open the

lid. And then take some measures to allow air to

escape from the load or reduce the volume of the

load.

(Refer to “5-6. Placing Articles to be Sterilized”.)

E23

The pressure drops because the exhaust

channel is blocked.

※

The pressure drops below the value

predicted by the chamber temperature by

equal to or less than 30kPa.

Turn off the power switch and wait until the

chamber pressure becomes 0MPa to open the

lid. Take out and place the load again so that the

hole in the chamber is not blocked. Open the

sterilization bag if it is closed.

E25

Control system malfunction

※

Memory abnormality

Unplug the power plug of the FLS-1000 from

the outlet and contact your dealer or our local

representative.

E26

Control system malfunction

※

Memory’s lifetime has expired.

Unplug the power plug of the FLS-1000 from

the outlet and contact your dealer or our local

representative.

E27

Control system malfunction

※

External temperature sensor for articles

to be sterilized is not adjusted.

Unplug the power plug of the FLS-1000 from

the outlet and contact your dealer or our local

representative.

E28

Control system malfunction

※

Chamber temperature sensor is not

adjusted.

Unplug the power plug of the FLS-1000 from

the outlet and contact your dealer or our local

representative.

Содержание FLS-1000

































































Результаты поиска

Содержание FLS-1000

Отзывы:

Похожие инструкции для FLS-1000

Бренды по названию

Популярные бренды

Tomy FLS-1000, Руководство оператора

Результаты поиска

Содержание FLS-1000

Отзывы:

Похожие инструкции для FLS-1000

Бренды по названию

Популярные бренды