manualshive.com logo in svg

Tomy FLS-1000, Руководство оператора

Поделиться
Скачать
Tomy FLS-1000 Скачать руководство пользователя страница 27

ー 26 ー

Check that the pressure gauge reads “0MPa”.

Check that the power switch is at “ON” position. 

Check that the IN PROGRESS indicator on the 

control panel turns off or the COMPLETED 

indicator in the work monitor display flashes.

Step on the lid-lock releasing pedal.

Pull up the lid gently by holding the chamber lid 

handle.

<

To open the chamber lid

>

①

②

③

④

⑤

Pull the lid down by holding the chamber lid handle.

Place hands on the chamber lid handle and push it down until the lid open indicator turns 

off.

<

To close the chamber lid

>

①

②

※

When the power switch is turned on with the lid being closed, the lid open indicator turns on. 

Open and then close the lid to activate the lid open/close detection system. 

※

The chamber lid may not be closed easily when the chamber temperature is still high immediately 

or shortly after the operation. In such a case, allow the chamber to cool and then close the lid. Do 

not apply excessive force to the lid handle. Deformation or damage may be caused.

Содержание FLS-1000

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды