Tomy FLS-1000 Скачать руководство пользователя страница 56

Страница: 56 / 64

ー 55 ー

9. TROUBLESHOOTING

If any system malfunction in the FLS-1000 is suspected, when it is operated properly according

to this Operator’s Manual, check the cause referring to the table below given in “9-1. Symptoms

and Solutions” and take the corresponding remedy. If the symptom of the malfunction is not

identified or the remedies described do not solve the problem, unplug the power plug of the

FLS-1000 from the outlet and contact your dealer or our local representative.

9-1. Symptoms and Solutions

Symptom

Possible cause

Remedy

No display appears on the control

panel when the power switch is

turned on.

FLS-1000 is not properly plugged.

Check the power cord for proper

connection.

Fuse or breaker at the power supply

side is blown or tripped.

Connect the power cord to the

power supply with the output

capacity required by the FLS-1000.

READY indicator does not turn

on.

Lid open indicator is on.

Check opening and closing of the lid

and then close the lid.

Low sterilizing water level indicator

is on.

Fill the chamber with water.

Drain indicator is on.

Drain the exhaust tank.

Drain access cover open indicator is

on.

Close the drain access cover.

Sterilizing water change indicator is

on.

Change water in the chamber.

Temperature rises slowly.

Extremely large amount of water is

in the chamber.

Check and adjust a level of water in

the chamber.

FLS-1000 is loaded with a large

amount of articles to be sterilized.

Check and adjust a volume of the

load.

Sterilization is not performed

sufficiently.

Sterilization time is insufficient.

Extend the sterilization time.

Steam leaks from the chamber lid. Chamber lid gasket or chamber

opening is covered with dust or dirt.

Clean the chamber lid gasket and

chamber opening.

Chamber lid gasket is damaged.

Unplug the power plug of the

FLS-1000 from the outlet and

contact your dealer or our local

representative.

Steam leaks from the safety valve. Chamber pressure is too high.

Unplug the power plug of the

FLS-1000 from the outlet and

contact your dealer or our local

representative.

The FLS-1000 won’t start or will

stop operation while displaying

an error code.

Take each remedy corresponding to the error code displayed, referring to

the “Error Code Table” given below.

Содержание FLS-1000

































































Результаты поиска

Содержание FLS-1000

Отзывы:

Похожие инструкции для FLS-1000

Бренды по названию

Популярные бренды

Tomy FLS-1000, Руководство оператора

Результаты поиска

Содержание FLS-1000

Отзывы:

Похожие инструкции для FLS-1000

Бренды по названию

Популярные бренды