background image

 

7 | 

P a g e

 

Tigo Energy, Inc.

 | 

www.tigoenergy.com

 | 

[email protected]

 

EI Residential Solution Overview 

The Tigo Energy Intelligence (EI) Battery provides energy resilience in the event of a grid 
outage and optimizes energy consumption based on rate plans for 

today’s home energy needs. 

The Tigo EI Battery is the energy st

orage component of Tigo’s Energy Intelligence Solution.

 

Each enclosure contains three battery modules for a total capacity of 9.9kWh.  

The Energy Intelligence Residential Solution 

The EI Residential Solution includes the following components:  

1.

 

EI Inverter

 

 The TSI-7.6K-US and TSI-11.4K-US inverters may be installed as grid-

tied only or as an energy storage system when paired with the EI Battery. The inverter 

converts the PV array’s DC energy to AC for 

use in the building and when paired with an 

EI Battery, acts as the battery management unit. 

2.

 

TS4 

 

Tigo’s 

MLPE, the TS4-A-F provides module-level rapid shutdown. The TS4-A-O 

provides module-level monitoring, rapid shutdown, and best-in-class module-level 

optimization with Tigo’s patented 

Predictive IV.  

3.

 

EI Battery

 (optional) 

 The LFP battery is designed for use specifically with the EI 

Inverter. Up to four battery enclosures may be installed with the EI Inverters. 

4.

 

EI ATS

 (required when batteries are used) 

 The EI ATS is an automatic transfer switch 

that switches the home loads from grid + Solar/battery usage to solar/battery usage 
only when the grid goes down. This is a required component of any energy storage 
system when connected to the utility grid as it prevents the potential for dangerous 
backfeed on the utility

’s

 conductors. 

5.

 

Energy Meter

 

 (optional / required when batteries are used) 

 The energy meter 

monitors the import and export of energy into the 

home’s

 electrical system. This allows 

the inverter to determine when and how much energy is required from the battery to 
serve connected loads. 

6.

 

Energy Intelligence 

 Accessible through the web or mobile app, the EI Platform 

provides visibility into system and module performance. The EI mobile app is also used 
for commissioning the EI Residential Solution. 

 

Figure 1 EI System Diagram 

5

 

6

 

Содержание TSB-10-US



































Отзывы: