background image

10

TC5-8SDA  rev.03

TC5-8SDA

TEMPERATURE PROBES

1

  Connecting the Probes

The controller is supplied with one temperature probe connected to input

# 1.  Three additional room probes can be connected to inputs # 2, 3 and

4  and an outside probe can be connected to input # 5 (see wiring

diagram enclosed).

CAUTION

: Probes operate at low voltage and are isolated from the

supply.  Be sure that probe cables remain insulated from all high voltage

sources.  In particular, do not route the probe cables through the same

electrical knockout as other cables.  Do not connect the shield from the

probe cable to a terminal or a ground.

Switches are used to activate or deactivate

the additional probes connected to the con-

troller.

Activate each additional probe by setting

the appropriate switch to 

ON

:

Switch # 3 activates the probe connected to input # 2.

Switch # 4 activates the probe connected to input # 3.

Switch # 5 activates the probe connected to input # 4.

2

  Extending the Probes

Each probe can be extended up to 500 feet (150 meters).  To extend a

probe:

Use a shielded cable of outside diameter between 0.245 and 0.260

in (6.22 and 6.60 mm) (the cable dimensions should not be under

18 AWG) to ensure the cable entry is liquid tight.  Do not ground

the shielding.

3

4

ON

5

Содержание TC5-8SDA



























































Отзывы: