Setting the date and time
To access the date and time settings:
•
With the
Utility
screen displayed, press the
arrow keys to highlight
Date/Time Setup
and
press
ENTER
. The screen displays the three
date/time options that you can modify - date,
time format and time.
To set the date:
•
Press the arrow keys to highlight
Set Date
and
press
ENTER
.
•
Press
Set Day
, type the date, then press
ENTER
.
•
Press
Set Month
, highlight the correct month,
then press
ENTER
.
•
Press
Set Year
, type the year, then press
ENTER
.
•
When the date is correct, press
ESC
to save
the settings and return to the
Utility
screen.
To select the time format:
You can set up the spectrophotometer to display
the time in either am/pm format or in 24-hour
format.
•
To change the display format for the time,
press the arrow keys to highlight
Time Format
and press
ENTER
until the format that you
want to use (AM/PM or 24 hour) appears.
To set the time:
•
Press the arrow keys to highlight
Set Time
and
press
ENTER
.
•
To set the hour, press
Set Hour
, type in the
hour and press
ENTER
.
•
To set the minutes, press
Set Minute
, type in
the minute and press
ENTER
.
•
To select between AM and PM, press
Set
AM/PM
until the appropriate setting appears.
Note:
Any changes you make are saved
automatically (even during power down) by
battery backup.
Selecting standby settings
To prolong xenon lamp life, your
spectrophotometer has been pre-set at the factory
to automatically go into standby mode after 15
minutes. To change Standby Mode time:
•
With the
Utility
screen displayed, press the
arrow keys to highlight
Standby
and press
ENTER
.
•
Press the arrow keys to highlight the length of
time you want the instrument will wait before
entering standby mode and press
ENTER
.
Setting baseline expiration time
If you will be performing scans on your samples,
you can set a time limit for a collected baseline.
To set the baseline expiration time:
•
With the
Utility
screen displayed, press the
arrow keys to highlight
Baseline Expiration
(hr:min) and press
ENTER
.
•
Enter the desired time into the Entry baseline
expiration time field. Press
ENTER
.
Setting the screen contrast
To make it easier to read the display, you can
adjust the screen contrast on the spectrophotometer.
•
With the
Utility
screen displayed, press the
arrow keys to highlight
Screen Contrast
and
press
ENTER
.
•
Press the arrow keys to adjust the screen
contrast.
•
When the screen contrast is correct, press
ESC
.
Setting up the internal printer
To set up the printer properly, you need to load the
paper and set the utility parameters for the printer.
Before setting up the parameters for the printer, be
sure that the printer is installed. If you have
ordered the internal printer as a separate item, you
will need to install it. Refer to the section
Connecting & using accessories
for instructions on
installing the printer.
Loading paper in the internal printer
Note:
Make sure that the paper roll holders are in
place as shown in Figure 3. When installed
correctly, they will fit flush with the top of
the instrument.
•
Cut the paper so the edge is even.
Note:
Arrows on the paper roll holders indicate
the direction of the paper feed (see
Figure 3).
Setting Up the Instrument
Thermo Electron Corporation
1-2
Содержание 335904
