Thermo Scientific TZ-32 Zonal Rotor Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 52

background image

Thermo Scientific TZ-32 Zonal Rotor

General Description — 35

4. Injection of sample and overlay

a. Pipe on the outer wall of the rotor

Clamp one end of the pipe at an outer position from the tee on the pump side, and put the other end into a

beaker for receiving the “cushion” discharged due to injection of sample and overlay.

b. Pipe on the rotor center

When the lightest gradient solution has filled the tee, clamp both ends of the pipe and stop the pump.Inject a

sample through one end by an injector. Then feed an overlay of 75 ml into the rotor.

➀

➁

➂

➂

➃

➄

➅

➆

➇

➈

CAUTION

Do not feed bubbles while injecting a density gradient solution and sample. Otherwise the gradient solution and

sample will be disturbed. If bubbles are about to enter, lead them to another tube from the tee by setting upright

the tube containing bubbles before they passthrough.

Figure 31

Injection of sample
and overlay

Figure 32

How to avoid
bubbles while
injecting a density
gradient solution
and sample

«
...
33
34
35
36
37
...
»

Содержание TZ-32 Zonal Rotor





















































Отзывы:

Нет отзывов

Похожие инструкции для TZ-32 Zonal Rotor

FX-ARM CONTROLLER

Бренд: Magicfx Страницы: 16

Бренд: UFO Страницы: 16

Бренд: Tascam Страницы: 8

Бренд: B-K lighting Страницы: 5

Бренд: B-K lighting Страницы: 4

Бренд: B-K lighting Страницы: 3

Бренд: Qiagen Страницы: 48

Бренд: Qiagen Страницы: 162

Бренд: Qazqa Страницы: 4

Бренд: Qlightec Страницы: 12

Chicken Coop Plan 3x5

Бренд: EASY COOPS Страницы: 21

Chicken Coop Plan 4x6

Бренд: EASY COOPS Страницы: 18

Chicken Coop Plan 8x10

Бренд: EASY COOPS Страницы: 18

Exitronix LEMD Series

Бренд: BARRON Страницы: 6

Бренд: Abus Страницы: 8

Бренд: Dangerous power Страницы: 38

Porta PlumeSafe 604

Бренд: Buffalo filter Страницы: 75

Бренд: Hettich Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды