manualshive.com logo in svg

Thermo Scientific TZ-32 Zonal Rotor, Инструкция по эксплуатации

Поделиться
Скачать
Thermo Scientific TZ-32 Zonal Rotor Скачать руководство пользователя страница 29

Thermo Scientific TZ-32 Zonal Rotor

 General Description — 29

 

5. 3. 

Operation

5. 3. 1.  Prepare the Rotor

1.  Put the seal packing and metal ring into the rotor. Put the O-ring into the extrusion on the center bottom of the rotor. 

Apply a thin coat of vacuum grease to the seal packing and O-ring.

CAUTION 

Set the seal packing and metal ring correct. If they are set incorrect, the seal packing comes out of the 

seal assembly, thus possibly causing the leakage of solution and damaging the rotor.

CAUTION 

Since O-ring and seal packing which are used in the rotor or the connecting portion of the seal section 

will come into contact with sample, always rinse them before use. When these parts are replaced, some 

residue generated when rubber was formed may remain on the surfaces of new parts. Rinse them away 

before use.

✓

✕

➀

Metal ring

➁

Seal packing

Figure 21

Setting the seal 
packing in detail

Содержание TZ-32 Zonal Rotor





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды