Thermo Scientific TZ-32 Zonal Rotor Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 52

background image

Thermo Scientific TZ-32 Zonal Rotor

Rotor Assembly — 19

5. Operation

CAUTION

Never spin the rotor at a speed over 5,000 rpm unless it is filled with the liquid.
If this is neglected, the septa will be damaged.

CAUTION

The over-speed decal, if corroded or discolored must be replaced immediately.
The over speed decal is important to control the rotor revolution speed.
The over-speed decal must match the maximum speed of the rotor.
When replacing be very careful not to damage the over-speed decal and rotor body.

Replacing over-speed decal

To replace the over-speed decal follow this procedure:

1. Preparation

»

Prepare a new over-speed decal and knife.

»

Wash and then dry the rotor well.

2. Hold the rotor upside down.

3. Pry the edge of the over-speed decal with the knife and remove the decal.

Be very careful not to damage the rotor.

4. Clean the decal hole on the rotor by using alcohol.

5. Remove the backing paper from the new over-speed decal.

Place the over-speed decal so that it fits into the groove of the decal hole on the rotor.

Make sure the decal does not move.

➀

➁

Part No. 34644414

➀

Over-speed decal

➁

Rotor

Figure 13

Overspeed decal
View from the
bottom

«
...
17
18
19
20
21
...
»

Содержание TZ-32 Zonal Rotor





















































Отзывы:

Нет отзывов

Похожие инструкции для TZ-32 Zonal Rotor

Бренд: Keithley Страницы: 36

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Yardistry Страницы: 9

Бренд: Makita Страницы: 84

Growers Supply 109722

Бренд: FarmTek Страницы: 9

Бренд: Farmi Forest Corporation Страницы: 32

Бренд: Garelick Страницы: 4

Бренд: iHealth Страницы: 8

Бренд: Kamikaze Страницы: 112

Бренд: KAM Страницы: 2

LED Street Bar 16x3W RGB IP65

Бренд: Varytec Страницы: 9

Бренд: VARILITE Страницы: 8

EVENTPROFILE VL800

Бренд: Vari Lite Страницы: 34

Optica 30 Series

Бренд: Varex Imaging Страницы: 36

Бренд: VDO Страницы: 15

Бренд: VDO Страницы: 20

Бренд: Xtricity Страницы: 4

Бренд: Nuvo Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды