manualshive.com logo in svg

Thermo Scientific TZ-32 Zonal Rotor, Инструкция по эксплуатации

Поделиться
Скачать
Thermo Scientific TZ-32 Zonal Rotor Скачать руководство пользователя страница 24

Thermo Scientific TZ-32 Zonal Rotor

 General Description — 24

 

Mounting the guard plate

Put the rotor on the spinning shaft and mount the guard plate.(In TZ-32, mount it to the upper hole in the 

support.) The guard plate can be fixed by inserting first the end of the fixed block into the left hole on the 

support, erecting the right knob and then turning it to horizontal.

➀

➁ ➂

➃

➄

➅

➆

➀

Fixed block

➁

Base

➂

Case

➃

Settler

➄

Knob

➅

Shaft

➆

Handle

Adjusting the base

a.  Loosen the four upper screws in the fixed block to make it movable. Then, loosen the lock nut of the setter. 

Move the fixed block and setter back and forth (by turning the setter) until the acryl plate is aligned with the 

rotor center. Tighten the screws to fix them.

➀

➁

➀

Lock nut

➁

Setter

Figure 15

Centering the guard 
plate

Figure 16

Loosening the lock 
nut

Содержание TZ-32 Zonal Rotor





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды