manualshive.com logo in svg

Thermo Scientific TZ-32 Zonal Rotor, Инструкция по эксплуатации

Поделиться
Скачать
Thermo Scientific TZ-32 Zonal Rotor Скачать руководство пользователя страница 16

Thermo Scientific TZ-32 Zonal Rotor

 Rotor Assembly — 16

 

4. 2. 

RPZ-S Seal Attachment Assembly

4. 2. 9.  Seal assembly

The seal assembly is mounted onto the rotor shaft as shown in 

Figure 10

. The rotor, shaft, and adapter rotate, but the other 

components do not rotate. The outer side of the holder cover is supported by the guard plate which will be described later.

The solution injected through the pipe is introduced through the body and Rulon seal into the rotor being spinned. One of 

the two higher pipes projecting from the body, which is located on the outer wall side of the rotor, is led to the outer groove 

of the Rulon seal and the outer wall of the rotor from the four septa vanes through the four holes of the Rulon seal. The 

pipe in the rotor center is led to the four holes on top of the septa through the center of the shaft. The two lower pipes are 

used for circulating cooling water into the interior of the body.

Figure 9

Seal assembly

Содержание TZ-32 Zonal Rotor





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды