manualshive.com logo in svg

Thermo Scientific TZ-32 Zonal Rotor, Инструкция по эксплуатации

Поделиться
Скачать
Thermo Scientific TZ-32 Zonal Rotor Скачать руководство пользователя страница 37

Thermo Scientific TZ-32 Zonal Rotor

 General Description — 37

 

5. 3. 5.  High speed spinning

1.  Place the cap

Hold the upper fringe as shown in the figure, and push it onto the shaft downwards.

CAUTION 

Make sure that the cap, once set completely, will not come off the shaft. Even when it is pulled holding 

the fringe. It is recommended to try setting the cap into the rotor as preliminary practice before spinning 

the rotor.

2.  Referring to the illustrations, check that the cap is set completely.

➀

The cap is set incompletely.

The cap is set completely.

➀

Push the fringe

3.  For the high speed spinning, 

see „5. 3. 3. Spinning“ on page 33

.

5. 3. 6.  Deceleration and extraction

1.  Regulation of the rotor speed to 3000 rpm by deceleration, 

see „5. 3. 3. Spinning“ on page 33

.

2.  Push the R. PUMP button and stop the vacuum pump to let air into the rotor chamber.

3.  Remove the cap.

Hold the running cap by both hands. Pull it upwards while pushing the center extrusion.

4.  Mount the seal assembly. 

See “5. 3. 4. Injection of gradient solution and sample” on page 33.

5.  Unloading the separated soultion by pump

a.  Pipe on the outer wall of rotor

Feed by pump with a heavy solution having a density equivalent to or higher than the maximum density of the 

Figure 35

Place the cap

Figure 36

Checking the cap

Содержание TZ-32 Zonal Rotor





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды