manualshive.com logo in svg

Thermo Scientific TZ-32 Zonal Rotor, Инструкция по эксплуатации

Поделиться
Скачать
Thermo Scientific TZ-32 Zonal Rotor Скачать руководство пользователя страница 3

Thermo Scientific TZ-32 Zonal Rotor

   — 3

 

5. 3. 2.  Preparation for spinning the rotor  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
5. 3. 3.  Spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5. 3. 4.  Injection of gradient solution and sample  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5. 3. 5.  High speed spinning  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
5. 3. 6.  Deceleration and extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

5. 4.  Operational Checkpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

5. 4. 1.  Setting of sample temperature and rotor temperature   . . . . . . . . . . . . . . . . . . . . . . 37
5. 4. 2.  Precautions on loading and unloading  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

5. 5.  Capacity in Rotor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

5. 6.  Separation Characteristic  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

5. 7.  Rotor Life  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

6.   Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

6. 1.  Cleaning of Rotor and Septa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

6. 2.  Sterilization of Rotor  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

6. 3.  Inspection of Rotors  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

6. 4.  Handling of Rulon Seal and Renewal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

6. 5.  Disassembling and Cleaning of Cap Assembly  . . . . . . . . . . . . . . . . . . . . 43

6. 6.  Disassembling and Cleaning of Seal Assembly   . . . . . . . . . . . . . . . . . . . 43

6. 7.  Cleaning of Ball Bearing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

6. 8.  Consumable Parts of the Rotor   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

6. 9.  Service Parts List for the Cap Assembly  . . . . . . . . . . . . . . . . . . . . . . . . . 45

6. 10.  Service Parts List for the Seal Assembly . . . . . . . . . . . . . . . . . . . . . . . . 46

7.   Troubleshooting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

7. 1.  Check the Rulon Seal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

7. 2.  Other Check Points  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Содержание TZ-32 Zonal Rotor





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды