manualshive.com logo in svg

Thermo Scientific TZ-32 Zonal Rotor, Инструкция по эксплуатации

Поделиться
Скачать
Thermo Scientific TZ-32 Zonal Rotor Скачать руководство пользователя страница 15

Thermo Scientific TZ-32 Zonal Rotor

 Rotor Assembly — 15

 

4. 1. 5.  Shaft

A shaft is inserted in the central part of septa, and form a sample passage way. And, the tops of the shaft become the 

installation of the cap and the connection part of seal assembly. The material of the shaft uses titanium alloy.

4. 1. 6.  Stopper

A stopper is the coming off stop part when a cap is installed, and material is Noryl.

4. 1. 7.  Rulon seal

The Rulon seal mouted on the top of shaft. This part is important component in loading and unloading, and material is 

fluorine plastic.

➀

➁

➂

4. 1. 8.  Cap assembly

The cap is mounted onto the shaft with the seal assembly removed after injecting a sample into the rotor. It seals the 

sample in the rotor when evacuating the rotor chamber and spinning the rotor at a high speed.

The cap can be easily and securely removed by pushing the extruded portion (push button) atop the cap.

Figure 7

Shaft, Stopper and 
Rulon Seal

Figure 8

Cap assembly

Содержание TZ-32 Zonal Rotor





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды