Главная
/
Thermo Scientific
/
GENESYS 10S Vis
/
Руководство пользователя

Thermo Scientific GENESYS 10S Vis, Руководство пользователя

Поделиться

105 страниц до
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134

Страница: 120 / 134

background image

22

Maintenance

Changing the Fuse

112

GENESYS 10S Vis User Guide

Thermo Scientific

Micro flowcells can be kept clean by:

• Flushing well with a solvent after use.

• Aspirating dilute acid, base, non-filming detergent or Clorox® through the cell in short

bursts.

• Storing with distilled water in the cell.

Cleaning the Windows of the Sample Compartment

Do not use acetone or abrasive materials to clean the windows of the sample compartment.
Instead, use a non-abrasive laboratory cleaning solution (such as a commercial cell cleaning
solution), distilled water or alcohol.

Use the liquid and a soft, lint-free cloth to clean the windows. Do not apply too much
pressure or the surface of the windows may be damaged. Be sure to remove all fingerprints.

Changing the Fuse

The fuse is located in the power entry module located at the center of the back panel of the
instrument.

• 120 VAC, 2.5 A, Slo Blo

• 240 VAC, 1.25 A, Slo Blo (2 required)

Y

To change the fuse

1. Turn off and unplug the instrument from the wall outlet or power strip.

2. Position the instrument so you can access the power entry module on the back of the

instrument.

3. Remove the power cord.

4. Insert a flat-blade screwdriver into the notch on the fuse cover and pry off the cover.

IMPORTANT

Do not dry cells in an oven.

IMPORTANT

The instrument fuse must be replaced with the same type and rate.

IMPORTANT

If the fuse fails repeatedly, it may indicate a serious problem with the

instrument. Contact technical support as soon as possible.

«
...
118
119
120
121
122
...
»

Содержание GENESYS 10S Vis







































































































































Отзывы:

Нет отзывов

Похожие инструкции для GENESYS 10S Vis

Бренд: Laica Страницы: 4

Tetrix 351 AC/DC Smart FW

Бренд: EWM Страницы: 117

Бренд: Harken Страницы: 4

Бренд: Harken Страницы: 2

TERRA FORCE BOOM

Бренд: Hardi Страницы: 40

Бренд: Harken Страницы: 4

QuickSlide HemaPRO

Бренд: Hardy Diagnostics Страницы: 2

Бренд: TDR Страницы: 8

EVENTWASH VL800

Бренд: Vari Lite Страницы: 23

Бренд: Vapotherm Страницы: 15

Бренд: Abus Страницы: 12

Бренд: Yamaha Страницы: 16

AirForm Night Splint

Бренд: Össur Страницы: 16

Бренд: Össur Страницы: 17

Бренд: Kärcher Страницы: 28

Бренд: Digilent Страницы: 14

Бренд: Fluke Страницы: 44

Бренд: natus Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды