Thermo Scientific GENESYS 10S Vis Скачать руководство пользователя страница 7

Страница: 7 / 134

Thermo Scientific

GENESYS 10S Vis User Guide

vii

Preface

Congratulations on your purchase of a Thermo Scientific spectrophotometer! Our
spectrophotometers integrate advanced hardware features with the power and flexibility of a
wide range of accessories.

Safety and Special Notices

Make sure you follow the precautionary statements presented in this guide. The safety and
other special notices appear in boxes.

Safety and special notices include the following:

Note

Notes contain helpful supplementary information.

IMPORTANT

Follow instructions labeled “Important” to avoid damaging the system

hardware or losing data.

CAUTION

Indicates a hazardous situation which, if not avoided, could result in minor or

moderate injury.

WARNING

Indicates a hazardous situation which, if not avoided, could result in death or

serious injury.

Содержание GENESYS 10S Vis







































































































































Результаты поиска

Содержание GENESYS 10S Vis

Отзывы:

Похожие инструкции для GENESYS 10S Vis

Бренды по названию

Популярные бренды

Thermo Scientific GENESYS 10S Vis, Руководство пользователя

Результаты поиска

Содержание GENESYS 10S Vis

Отзывы:

Похожие инструкции для GENESYS 10S Vis

Бренды по названию

Популярные бренды