Thermo Scientific GENESYS 10S Vis Скачать руководство пользователя страница 31

Страница: 31 / 134

Accessories

External Printers

Thermo Scientific

GENESYS 10S Vis User Guide

To load paper in the internal printer

1. Cut the paper so the edge is even.

2. Feed the paper straight into the paper entry slot.

The printer grabs the end of the paper and pulls it in.

3. In Basic ATC mode, when the paper stops, press

Enter

to continue advancing the paper

until the paper comes out of the paper exit slot.

4. Pull out on the finger tabs on the paper roll holders and secure the roll of paper onto the

paper roll holder.

External Printers

Your spectrophotometer is able to print to external desktop printers supporting HP PCL 5.0
format and later.

To print to an HP PCL printer, connect the USB cable to the printer and to the USB port on
the back of the instrument (see

“Connectors”

page 1

Note

Make sure the paper roll holders are in place as shown. When installed correctly,

they fit flush with the top of the instrument.

Note

Arrows on the paper roll holders indicate the direction of the paper feed.

Note

PCL format does not support HP “Windows” printers.

Note

The instrument is compatible with most HP PCL printers; brands other than HP

will also be supported. If the printer is not purchased from Thermo Scientific, it is your
responsibility to determine if the printer is compatible with the instrument. Contact
technical support or your sales representative for more information.

Содержание GENESYS 10S Vis







































































































































Результаты поиска

Содержание GENESYS 10S Vis

Отзывы:

Похожие инструкции для GENESYS 10S Vis

Бренды по названию

Популярные бренды

Thermo Scientific GENESYS 10S Vis, Руководство пользователя

Результаты поиска

Содержание GENESYS 10S Vis

Отзывы:

Похожие инструкции для GENESYS 10S Vis

Бренды по названию

Популярные бренды