Thermo Scientific GENESYS 10S Vis Скачать руководство пользователя страница 108

Страница: 108 / 134

Performance Verification

Troubleshooting Checklist

100

GENESYS 10S Vis User Guide

Thermo Scientific

Troubleshooting Checklist

If a Performance Verification test fails, follow the instructions below to diagnose common
problems.

If a test continues to fail after you have tried all these recommendations, follow the
troubleshooting list for the test being run (included with the description of each test).

Make sure:

• You follow the instructions for the test properly.

• Filters and standards are clean.

• The sample compartment door is closed during the test.

• The sample compartment is clear of obstructions.

• The cell holder assembly is installed properly. If the 6-Position Cell Holder is installed,

run the test once with the sample compartment door open to verify that the 6-Position
Cell Holder is moving smoothly.

• No problems are indicated by the power-on diagnostics after you turn the instrument

power OFF and then ON.

• The lamp is ON.

• The lamp compartment is clear of obstructions.

WARNING

Do not open the lamp compartment unless the instrument power is OFF.

WARNING

Do not turn the instrument power ON unless the lamp compartment is

closed.

Содержание GENESYS 10S Vis







































































































































Результаты поиска

Содержание GENESYS 10S Vis

Отзывы:

Похожие инструкции для GENESYS 10S Vis

Бренды по названию

Популярные бренды

Thermo Scientific GENESYS 10S Vis, Руководство пользователя

Результаты поиска

Содержание GENESYS 10S Vis

Отзывы:

Похожие инструкции для GENESYS 10S Vis

Бренды по названию

Популярные бренды