Thermal Dynamics PAK 200 Скачать руководство пользователя

Страница: 89 / 114

Manual 0-5057

7-7

TORCH MAINTENANCE

PAK 200

head then tighten the threaded locking nut against

the torch handle.

NOTE

There will be a slight gap between the torch

head and the lock nut.

7.07 Servicing Machine Torch

Components

WARNINGS

Disconnect primary power to the system before

disassembling the torch or torch leads.

DO NOT touch any internal torch parts while

the AC indicator light on the front panel of the

Power Supply is ON.

A. Removing Machine Torch Head

1. Remove the shield cup, tip, gas distributor and

electrode from the torch head assembly.

2. Remove shrink on tubing.
3. Locate the tape at the back end of the torch posi-

tioning tube. Remove the tape from the torch lead

sleeving and slide the sleeving back (see NOTE).

NOTE

The positioning tube will not slide over the torch

lead sleeving.

4. Unscrew the positioning tube from the torch

adaptor on the torch head assembly and slide the

positioning tube back over the leads.

5. Unscrew the torch adaptor from the torch head

assembly. Slide the torch adaptor back over the

leads to expose the plasma (+), secondary, coolant

supply (-), and coolant return connectors.

Positioning Tube

Torch Adaptor

Lead Connections

A-00663

Bushing

Pinion Assembly

Machine

Torch Head

Torch Mounting Assembly

6. Disconnect the plasma (+), secondary, coolant

supply (-), and coolant return connectors to allow

removal of the torch head. Note the location of the

torch leads insulator which separates the negative

and positive leads.

Plasma Lead (+)

Coolant Return Lead

(LH Threads)

Secondary Lead

Coolant (-)

Supply Lead

A-02198

Torch Head Removal

B. Reassembling Machine Torch Assembly

NOTE

Verify that the small rubber duck valve is in

torch plasma fitting.

1. Remove the rigid insulator from the old Torch Head

Assembly from between the layers of estermat

paper.

Содержание PAK 200



















































































































Результаты поиска

Содержание PAK 200

Отзывы:

Похожие инструкции для PAK 200

Бренды по названию

Популярные бренды

Thermal Dynamics PAK 200, Руководство по эксплуатации

Результаты поиска

Содержание PAK 200

Отзывы:

Похожие инструкции для PAK 200

Бренды по названию

Популярные бренды