Thermal Dynamics PAK 200 Скачать руководство пользователя

Страница: 43 / 114

PAK 200

Manual 0-5057 4-1 OP-

SECTION 4:

OPERATION

4.01 Power Supply Indicators

Art # A-04813

AC Indicator

Temp Indicator

Gas Indicator

DC Indicator

Status Indicator

AC Power Indicator

Indicates AC power is being supplied to the inverters when the ON/OFF switch is in ON position. When switch is

first set to ON, the indicator stays off until the inrush cycle is complete and the correct voltage is confirmed.

TEMP Indicator: Normally OFF. Indicator turns ON when the internal temperature sensors detect tempera-

tures above normal limits. Let the unit cool before continuing operation.

GAS Indicator: The indicator blinks when the gas control is not ready. Causes for not being ready are when

purging, Run/Set switch is not set to Run, gas pressure is not correct. When gas flow is called for (preflow,

cutting, postflow ) the indicator is on steady. It is off at all other times.

DC Indicator: Indicates the power supply is generating output DC voltage.

Status Indicator: Shows system status. The number of flashes indicates the status. Refer to the

Status Code Section for details. On power supply start-up, the indicator flashes to show the revision level of

the operating software installed in the system.

Содержание PAK 200



















































































































Результаты поиска

Содержание PAK 200

Отзывы:

Похожие инструкции для PAK 200

Бренды по названию

Популярные бренды

Thermal Dynamics PAK 200, Руководство по эксплуатации

Результаты поиска

Содержание PAK 200

Отзывы:

Похожие инструкции для PAK 200

Бренды по названию

Популярные бренды