Thermal Dynamics PAK 200 Скачать руководство пользователя

Страница: 37 / 114

Manual 0-5057

3-13

INSTALLATION

PAK 200

3.10 Connect Torch Leads to the Gas Control Module / Arc Starter

1. Remove the top cover from the Gas Control Module / Arc Starter.
2. Pass the torch leads and coolant leads through the torch leads port on the back of the module. Ensure that the

leads outer jacket slides into the port.

CAUTION

Use protective gloves when handling the leads. Do not kink or bend the leads.

3. Connect the leads to the module in the sequence shown. Coolant leads and connectors are color-tagged; red

for coolant return, green for coolant supply. Shield gas and plasma gas connections are left- and right- hand

threaded and will not interchange.

Torch Leads: Coolant Supply & Return

Plasma Gas

Shield Gas

Art #: A-008382

Содержание PAK 200



















































































































Результаты поиска

Содержание PAK 200

Отзывы:

Похожие инструкции для PAK 200

Бренды по названию

Популярные бренды

Thermal Dynamics PAK 200, Руководство по эксплуатации

Результаты поиска

Содержание PAK 200

Отзывы:

Похожие инструкции для PAK 200

Бренды по названию

Популярные бренды