Thermal Arc A-07360 Скачать руководство пользователя страница 68

Страница: 68 / 102

FABRICATOR 210

7-8

June 19, 2006

3. Defective MIG GUN / SPOOL GUN SELECTOR

SWITCH SW2

a. Check continuity of SW2.

4. Defective WIRE FEED MOTOR M2

a. With Gun Switch closed, measure for approx

2-16 VDC variation at the control PCB between
JB-6 to JB-8 as the WIRE SPEED CONTROL
potentiometer is varied from minimum to
maximum. If voltage is correct, replace motor.

5. Open wire from Rectifier assembly to Control PCB

a. With gun switch closed, measure for approx

27 VDC at Control PCB between JB7 (-) to JB9
(+). If no voltage, check wire continuity and
replace open wire.

6. Faulty MAIN PCB

a. With gun switch closed, measure voltage

between JB-6(-) to JB-8 (+) for approx 10 VDC.
If voltage is 0 VDC, replace Control PCB.

7. Defective FINE or COARSE VOLTAGE CONTROL

SWITCH.

a. See VOLTAGE CONTROL SWITCH test

procedure, page 7-11.

8. Defective Rectifier assembly

a) Check per the diode test procedure page 7.16.

9. Defective Main transformer

a. Check main transformer per test procedure

page 7.17.

7.10 Spool Gun Control (J1) Problem

A. Gas does not flow when jumper is connected

between J11 Pins D & G

1. Defective gas solenoid SOL2

a. Measure for 32VAC at SOL2 between Orange

wires (# 31C) and Violet wire (#58). If voltage
is correct replace SOL2. For all other issues
regarding J11 check SW2.

7.11 Output Voltage Problem

A. Output is low in one or more OUTPUT VOLTAGE

CONTROL SWITCH positions

1. Defective OUTPUT VOLTAGE SELECTION SWITCH

a. Check continuity of switch. See test procedure

on page 7-11.

2. Defective MAIN TRANSFORMER

a. Check Main transformer per test procedure on

page 7-14.

7.12 Wire Feed and Weld Problems

A. Poor or inconsistent arc transfer or no arc transfer

1. Poor work cable connection or open work cable

a. Clean contact point, check continuity of cable

and cable to clamp connection. Replace if work
cable if required.

B. Wire feed and welding problems

(Refer to sections 6.03 & 6.03 )

Содержание A-07360







































































































Результаты поиска

Содержание A-07360

Отзывы:

Thermal Arc A-07360, Руководство по обслуживанию, Страница: 68 / 102

Результаты поиска

Содержание A-07360

Отзывы: