Thermal Arc A-07360 Скачать руководство пользователя страница 40

Страница: 40 / 102

FABRICATOR 210

4-4

June 19, 2006

4.02 Weld Mode Selector

The Weld Mode Selecto

switch selects the method of welding mode.

BURNBACK

WELD MODE

MIN

WELD

(

POT /

TITCH)

(

POT /

TITCH)

(

TITCH)

(

TITCH)

POT

TITCH

MIN

DWELL

Art # A-07183

Figu

e 4-5: Inte

nal Welding Cont

ols

2T (Continuous Welding):

This mode of welding is used to weld two o

components togethe

with a continuous weld. When

the MIG gun t

igge

switch is dep

essed welding

commences. When the MIG gun t

igge

switch is

eleased welding ceases.

WELD MODE

POT

TITCH

Art # A-07427

Figu

e 4-6: Fo

Refe

ence Only

SPOT:

This mode of welding is used to weld two plates
togethe

at a desi

ed location by melting the top &

bottom plates togethe

to fo

m a nugget between

them. The spot time pe

iod is set by the Weld (Spot/

Stitch) cont

ol knob located in the elect

ode wi

compa

tment.

Art # A-07466

Figu

e 4-7: Spot Weld

NOTE

A spot nozzle should be used on the MIG gun
to obtain consistent spot welds.

Содержание A-07360







































































































Результаты поиска

Содержание A-07360

Отзывы:

Thermal Arc A-07360, Руководство по обслуживанию, Страница: 40 / 102

Результаты поиска

Содержание A-07360

Отзывы: