manualshive.com logo in svg

Thermal Arc A-07360, Руководство по обслуживанию, Страница: 26 / 102

Поделиться
Скачать
Thermal Arc A-07360 Скачать руководство пользователя страница 26

FABRICATOR 210

3-6

June 19, 2006

Adjusting Regulator

Adjust cont

r

ol knob of 

r

egulato

r

 to the 

r

equi

r

ed flow 

r

ate, indicated on gauge dial. (Refe

r

 to Figu

r

e 3-3)

The gas flow 

r

ate should be adequate to cove

r

 the weld zone to stop weld po

r

osity. Excessive gas flow 

r

ates may cause

tu

r

bulence and weld po

r

osity.

A

r

gon o

r

 a

r

gon based gas flow 

r

ates:

 - Wo

r

kshop welding: 20-30 CFH

 - Outdoo

r

s welding: 30-40 CFH

Helium based o

r

 CO2 gas flow 

r

ates:

 - Wo

r

kshop welding: 30-40 CFH

 - Outdoo

r

s welding: 40-50 CFH

NOTE

All valves downst

r

eam of the 

r

egulato

r

 must be opened to obtain a t

r

ue flow 

r

ate 

r

eading

on the outlet gauge. (Welding powe

r

 sou

r

ce must be t

r

igge

r

ed) Close the valves afte

r

 the

p

r

essu

r

e has been set.

Art # A-07280

Figu

r

e 3-3: Adjusting Flow Rate

Refe

r

 to section 4.09 fo

r

 suggested gas / fille

r

 metal combinations.

NOTE

The 

r

egulato

r

/flow mete

r

 used with a

r

gon based and ca

r

bon dioxide shielding gases is

diffe

r

ent. The 

r

egulato

r

/flow mete

r

 supplied is fo

r

  a

r

gon based shielding gases. If ca

r

bon

dioxide is to be used a suitable ca

r

bon dioxide 

r

egulato

r

/flow mete

r

 will need to be fitted.

Содержание A-07360







































































































Отзывы:

Нет отзывов