Texas Instruments SimpleLink CC2652PSIP, Руководство пользователя

Страница: 14 / 68

Measured on the CC2652xSIP-EM reference design with T
c
= 25 °C, V
DDS
= 3.0 V, f
RF
= 2440 MHz with
DC/DC enabled and high power PA connected to V
DDS
unless otherwise noted.
All measurements are performed at the antenna input with a combined RX and TX path, except for high power PA which is
measured at a dedicated antenna connection. All measurements are performed conducted.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Selectivity, ±6 MHz
(1)
Wanted signal at –72 dBm, modulated interferer at ≥ ±6
MHz, BER = 10
–3
46 / 45
(2)
dB
Selectivity, ±7 MHz
Wanted signal at –72 dBm, modulated interferer at ≥ ±7
MHz, BER = 10
–3
49 / 45
(2)
dB
Selectivity, Image frequency
(1)
Wanted signal at –72 dBm, modulated interferer at image
frequency, BER = 10
–3
35 dB
Selectivity, Image frequency ±1
MHz
(1)
Note that Image fre 1 MHz is the Co- channel
–1 MHz. Wanted signal at –72 dBm, modulated interferer
at ±1 MHz from image frequency, BER = 10
–3
4 / 46
(2)
dB
1 Mbps (LE 1M)
Receiver sensitivity Differential mode. BER = 10
–3
–96 dBm
Receiver saturation Differential mode. BER = 10
–3
> 5 dBm
Frequency error tolerance
Difference between the incoming carrier frequency and
the internally generated carrier frequency
> (–350 / 350) kHz
Data rate error tolerance
Difference between incoming data rate and the internally
generated data rate (37-byte packets)
> (–650 / 750) ppm
Co-channel rejection
(1)
Wanted signal at –67 dBm, modulated interferer in
channel, BER = 10
–3
–6 dB
Selectivity, ±1 MHz
(1)
Wanted signal at –67 dBm, modulated interferer at ±1
MHz, BER = 10
–3
7 / 4
(2)
dB
Selectivity, ±2 MHz
(1)
Wanted signal at –67 dBm, modulated interferer at ±2
MHz,BER = 10
–3
39 / 33
(2)
dB
Selectivity, ±3 MHz
(1)
Wanted signal at –67 dBm, modulated interferer at ±3
MHz, BER = 10
–3
36 / 40
(2)
dB
Selectivity, ±4 MHz
(1)
Wanted signal at –67 dBm, modulated interferer at ±4
MHz, BER = 10
–3
36 / 45
(2)
dB
Selectivity, ±5 MHz or more
(1)
Wanted signal at –67 dBm, modulated interferer at ≥ ±5
MHz, BER = 10
–3
40 dB
Selectivity, image frequency
(1)
Wanted signal at –67 dBm, modulated interferer at image
frequency, BER = 10
–3
33 dB
Selectivity, image frequency
±1 MHz
(1)
Note that Image fre 1 MHz is the Co- channel
–1 MHz. Wanted signal at –67 dBm, modulated interferer
at ±1 MHz from image frequency, BER = 10
–3
4 / 41
(2)
dB
Out-of-band blocking
(3)
30 MHz to 2000 MHz –10 dBm
Out-of-band blocking 2003 MHz to 2399 MHz –18 dBm
Out-of-band blocking 2484 MHz to 2997 MHz –12 dBm
Out-of-band blocking 3000 MHz to 12.75 GHz –2 dBm
Intermodulation
Wanted signal at 2402 MHz, –64 dBm. Two interferers
at 2405 and 2408 MHz respectively, at the given power
level
–42 dBm
Spurious emissions,
30 to 1000 MHz
(4)
Measurement in a 50-Ω single-ended load. < –59 dBm
Spurious emissions,
1 to 12.75 GHz
(4)
Measurement in a 50-Ω single-ended load. < –47 dBm
RSSI dynamic range 70 dB
RSSI accuracy ±4 dB
2 Mbps (LE 2M)
Receiver sensitivity
Differential mode. Measured at SMA connector, BER =
10
–3
–90 dBm
Receiver saturation
Differential mode. Measured at SMA connector, BER =
10
–3
> 5 dBm
Frequency error tolerance
Difference between the incoming carrier frequency and
the internally generated carrier frequency
> (–500 / 500) kHz
Data rate error tolerance
Difference between incoming data rate and the internally
generated data rate (37-byte packets)
> (–700 / 750) ppm
CC2652PSIP
SWRS263A – FEBRUARY 2021 – REVISED JUNE 2022
www.ti.com
14 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: CC2652PSIP