manualshive.com logo in svg

Texas Instruments MSP430x4xx Family, Руководство пользователя


Поделиться
Скачать
background image

Scan IF Operation

30-16

Scan IF

TSM Operation

The TSM automatically starts and re-starts periodically based on a divided
ACLK start signal selected with the SIFDIV2x bits, the SIFDIV3Ax and
SIFDIV3Bx bits when SIFTSMRP = 0. For example, if SIFDIV3A and
SIFDIV3B are configured to 270 ACLK cycles, then the TSM automatically
starts every 270 ACLK cycles. When SIFTSMRP = 1 the TSM re−starts
immediately with the SIFTSM0 state at the end of the previous sequence i.e.
with the next ACLK cycle after encountering a state with SIFSTOP = 1. The
SIFIFG2 interrupt flag is set when the TSM starts.

The SIFDIV3Ax and SIFDIV3Bx bits may be updated anytime during
operation. When updated, the current TSM sequence will continue with the old
settings until the last state of the sequence completes. The new settings will
take affect at the start of the next sequence.

TSM Control of the AFE

The TSM controls the AFE with the SIFCHx, SIFLCEN, SIFEX, SIFCA,
SIFRSON, SIFTESTS1, SIFDAC, and SIFSTOP bits. When any of these bits
are set, their corresponding signal(s),  SIFCHx(tsm), SIFLCEN(tsm),
SIFEX(tsm), SIFCA(tsm), SIFRSON(tsm), SIFTESTS1(tsm), SIFDAC(tsm),
and SIFSTOP(tsm) are high for the duration of the state. Otherwise, the
corresponding signal(s) are low.

TSM State Duration

The duration of each state is individually configurable with the SIFREPEATx
bits. The duration of each state is SIFR 1 times the selected clock
source. For example, if a state were defined with SIFREPEATx = 3 and
SIFACLK = 1, the duration of that state would be 4 x ACLK cycles. Because
of clock synchronization, the duration of each state is affected by the clock
source for the previous state, as shown in Table 30−5.

Table 30−5.TSM State Duration

SIFACLK

For

Previous

State

For

Current

State

State Duration, T

0

0

T = (SIFR 1) x 1/f

SIFCLK

0

1

(SIFREPEATx) x 1/f

ACLK

 

t

 T 

v

 (SIFR 1) x

1/f

ACLK

1

0

(SIFR 1) x 1/f

SIFCLK

 

v

 T 

t

 (SIFR 2) x

1/f

SIFCLK

1

1

T = (SIFR 1) x 1/f

ACLK

Содержание MSP430x4xx Family








































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MSP430x4xx Family

NAIM AV2 Update Instructions preview
AV2
Бренд: NAIM Страницы: 2
Vanguard 342 Quick Reference Manual preview
342
Бренд: Vanguard Страницы: 4
Measurement Computing PC-CARD DAS16 User Manual preview
PC-CARD DAS16
Бренд: Measurement Computing Страницы: 27
FOR-A USF-105PS Operation Manuals preview
USF-105PS
Бренд: FOR-A Страницы: 37
SilverStone argon series User Manual preview
argon series
Бренд: SilverStone Страницы: 16
Juniper MX104 Quick Start Manual preview
MX104
Бренд: Juniper Страницы: 30
XMOS MultiUART Quick Start Manual preview
MultiUART
Бренд: XMOS Страницы: 8
Rosewill RC-611 User Manual preview
RC-611
Бренд: Rosewill Страницы: 5
IBA ibaPADU-S-IT-16 Manual preview
ibaPADU-S-IT-16
Бренд: IBA Страницы: 80
Extron electronics IPL Pro Series User Manual preview
IPL Pro Series
Бренд: Extron electronics Страницы: 10
Dell A2463645 - 2 GB Memory Manuallines preview
A2463645 - 2 GB Memory
Бренд: Dell Страницы: 2
TRENDnet TEG-S4M1FGL Supplementary Manual preview
TEG-S4M1FGL
Бренд: TRENDnet Страницы: 1
KWorld DVB-S 100 Faq preview
DVB-S 100
Бренд: KWorld Страницы: 18
Sony VPCEB1 Series Safety Information Manual preview
VPCEB1 Series
Бренд: Sony Страницы: 24
Sony VAIO VGN-N200 Series User Manual preview
VAIO VGN-N200 Series
Бренд: Sony Страницы: 153
Sony VGN-NR100 Series User Manual preview
VGN-NR100 Series
Бренд: Sony Страницы: 158
Sony VAIO VGN-TXN10 Series User Manual preview
VAIO VGN-TXN10 Series
Бренд: Sony Страницы: 212
Sandberg Nano User Manual preview
Nano
Бренд: Sandberg Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды