manualshive.com logo in svg

Tescom TC-5942B, Руководство по эксплуатации, Страница: 9 / 47

Поделиться
Скачать
Tescom TC-5942B Скачать руководство пользователя страница 9

 

 
 
                                          

1-3

 

 Connectors                                             

This section contains reference information for TC-5942B’s connectors. 

Table 1-1 

 TC-5942B Connectors   

Connector 

Specification 

RS-232C (Communication between the TC-

5942B and other instruments or computers). 

Working Voltage: 100V 

Dielectric Withstanding Voltage: 300V 

EMI Filter: 1000 pF Pi 

N Coaxial Connector of the outside 

(Input RF signals, Connected to SMA 

connector of the inside) 

Impedance: 50 ohm 

Voltage Rating; 1500 Vpeak 

Dielectric Withstanding Voltage: 2500 Vrms 

SMA Coaxial Connector of the inside 

(Connection with DUT) 

Impedance: 50 ohm 

Voltage Rating; 250 Vpeak 

Dielectric Withstanding Voltage: 750 Vrms 

9 Pin D-Type Data Connector   

(Outside: Input Data signals,   

Inside: Connection with DUT) 

Working Voltage: 100V 

Dielectric Withstanding Voltage: 300V 

EMI Filter: 1000 pF Pi 

25 Pin D-Type Data Connector   

(Outside: Input Data signals,   

Inside: Connection with DUT)   

Working Voltage: 100V 

Dielectric Withstanding Voltage: 300V 

EMI Filter: 1000 pF Pi 

1-3 Connectors 

Содержание TC-5942B
















































Отзывы:

Нет отзывов