manualshive.com logo in svg

Tescom TC-5942B, Руководство по эксплуатации, Страница: 5 / 47

Поделиться
Скачать
Tescom TC-5942B Скачать руководство пользователя страница 5

 

 
 
                                          

v

 

Safety Symbols and Terms 

 

Terms in this manual:

   

WARNING

: Identifies conditions or practices that could result in injury or loss of life. 

CAUTION

: Identifies conditions or practices that could result in damage to the product or other 

property.   

 

Terms on the product:

   

DANGER

: Indicates an injury hazard immediately accessible as you read the marking. 

WARNING

: Indicates an injury hazard not immediately accessible as you read the marking. 

CAUTION

: Indicates a hazard to property including the product. 

 

Symbols on the Product:

 The following symbols may appear on the product. 

 

 

 

 

 

 

 Service and Support                                    

       

 

If you have a problem with your TC-5942B, contact Tescom Technical Support specialists. 

Any adjustment or repair of this product must be performed by qualified personnel. 

 

Contact Information   

Address:

 TESCOM Company Limited 

Suite 927 UNITECHVIL, Ilsan, Koyang, Kyunggi, Korea (ZIP 411-722)   

TEL:

 82-31-905-0513       

FAX:

 82-31-902-0514   

Email: 

[email protected],  [email protected]   

Internet:

 http://www.tescom-lab.com

 

DANGER 

Risk of electric shock 

ATTENTION 

Refer to Manual 

Indicates earth 

(ground) terminal 

WARNING 

Proper precaution must 

be taken while the lid is  

open and closed.   

Содержание TC-5942B
















































Отзывы:

Нет отзывов