Tescom TC-5942B Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 47

Tescom TC-5942B Скачать руководство пользователя страница 18

3-3

Remote Operation Using RS-232C

TC-5942B supports high speed RS-232C serial interface for remote operation under PC control. A

standard 9-pin RS-232C connector is located at the left side. Any communication program (such as

WINDOW 95/98 Hyper Terminal) could be used for simple tasks. Complex tasks can be automated

using PC programming.

RS-232C Connection

A 9-pin standard connector is used in the TC -5942B for a RS-232C connection. To make a

connection to the 25-pin RS-232C connector, a 9-pin to 25-pin adapter can be used. The cable pin

configuration is shown below.

Figure 3-1

RS-232C Connection

PC Control Using Communication Program

Windows 95/98 Hyper Terminal

1 PC Setup

A. Check for the Hyper Terminal installation on your PC. Click Start

→

Program

→

Accessories

→

(Communications). If Hyper Terminal folder is not found in the Accessories list, it must be

installed. Insert Windows 95 or 98 CD ROM and install Hyperterminal program.

B. Start Hyper Terminal: Click Start

→

Program

→

Accessories

→

(Communications) and then

click “Hyper Terminal”.

C. On “Hyper Terminal” screen, double click “Hypertrm” icon.

D. In “Name” block, on “New Connections” screen, enter “TC-5942B”. Select a desired icon and

click “OK”.

3-2 Remote Operation Using RS-232C

«
...
16
17
18
19
20
...
»

Содержание TC-5942B
















































Отзывы:

Нет отзывов