Terex TA30, Руководство по обслуживанию

Страница: 102 / 410

Section 130-0010
Drivelines - Front and Rear Drivelines
SM 1534 Rev 1 3-00
4
Note: Do not distort the tube with excessive grip.
2. Install cross assembly (2) to yoke end of driveline
assembly (1) and secure with capscrews (10).
3. Place the shaft end of driveline assembly (1) in a
soft jawed vice.
4. Install cross assembly (2) to shaft end of driveline
assembly (1) and secure with capscrews (10).
5. Repeat steps 1 to 4 for drivelines (4 & 6) and
(2 & 5, Fig. 2)
INSTALLATION
Numbers in parentheses refer to Fig. 1, unless
otherwise specified.
Note: Tighten all fasteners without special torques
specified to standard torques listed in Section
300-0080, STANDARD BOLT AND NUT TORQUE
SPECIFICATIONS.
Note: Extra care should be taken when handling
drivelines since carelessness can result in premature
failure of the components. Chips, dents, burrs, or any
other deformity of wing bearings will prevent accurate
mating. This will cause misalignment which is
accompanied by vibration and excessive wear.
WARNINGS
To prevent personal injury and property
damage, be sure wheel blocks, blocking
materials and lifting equipment are properly
secured and of adequate capacity to do the job
safely.
To prevent serious injury or death, DO
NOT go under the vehicle when the engine is
running. Rotating shafts can be dangerous.
You can snag clothes, skin, hair, hands, etc..
1. Position driveline assembly (6) on the vehicle as
shown in Fig. 1 and align match marks on cross
assemblies (7) with those on its mating surfaces.
2. Apply Loctite 243 to the threads of capscrews (9)
and secure cross assemblies (7) to its mating surfaces
with capscrews (9). Tighten capscrews (9) to a torque
of 153 Nm (113 lbf ft).
3. Position driveline assembly (4) on the vehicle as
shown in Fig. 1 and align match marks on cross
assemblies (5) with those on its mating surfaces.
4. Apply Loctite 243 to the threads of capscrews (10)
and secure cross assemblies (5) to its mating surfaces
with capscrews (10). Tighten capscrews (10) to a
torque of 153 Nm (113 lbf ft).
5. Position driveline assembly (1) on the vehicle as
shown in Fig. 1 and align match marks on cross
assemblies (2) with those on its mating surfaces.
6. Apply Loctite 243 to the threads of capscrews (10)
and secure cross assemblies (2) to its mating surfaces
with capscrews (10). Tighten capscrews (10) to a
torque of 153 Nm (113 lbf ft).
7. Secure bracket (11) over driveline assembly (1) and
onto engine crossmember with bolts (12), washers
(13) and locknuts (14).
8. Secure access plate to cab floor with mounting
hardware removed during removal. Place cab floor
mat in position and ensure that all pedals are free to
operate.
9. Position driveline assembly (2, Fig. 2) on the vehicle
as shown and align match marks on cross assemblies
(3, Fig. 2) with those on its mating surfaces.
11. Apply Loctite 243 to the threads of capscrews
(1, Fig. 2) and secure cross assemblies (3, Fig. 2) to
its mating surfaces with capscrews (1, Fig. 2). Tighten
capscrews (1, Fig. 2) to a torque of 153 Nm
(113 lbf ft).
12. Position driveline assembly (5, Fig. 2) on the
vehicle as shown and align match marks on cross
assemblies (6, Fig. 2) with those on its mating
surfaces.
13. Apply Loctite 243 to the threads of capscrews
(1, Fig. 2) and secure cross assemblies (6, Fig. 2) to
its mating surfaces with capscrews (1, Fig. 2). Tighten
capscrews (1, Fig. 2) to a torque of 153 Nm
(113 lbf ft).
14. Place the battery master switch in the 'On'
position, ensure the parking brake is applied and start
the engine. Remove wheel blocks from all road
wheels.
Courtesy of Machine.Market