manualshive.com logo in svg

Tennant A60, Руководство оператора

Поделиться
Скачать
Tennant A60 Скачать руководство пользователя страница 17

 

TENNANT A60

 

 

 

 

 

English                                                                                                                                      1064354 rev. 00 

 

- 17 -

Working on the battery: 

»  No open fire and no smoking. 
»  Avoid acid from coming into contact with clothing or skin. 
 

In the event of acid injuries, rinse well with clean water and 
contact a doctor. 

 
»  Never place any tools on the battery. 
»  When recharging the battery, remove the caps to avoid a build-up of explosive gases. 
»  Treat old batteries in accordance with legal stipulations. 
 

Working on the fuel system 

»  No open fire and no smoking. 
»  Avoid spilling fuel. Catch spilt fuel and prevent it from seeping into the ground. 
 

Cleaning 

»  Never carry out any cleaning activities while the engine is running. 
»  Never use petrol or other highly flammable substances for cleaning. 
»  Do not expose the electrical parts to steam jets when using a steam cleaner.  Do not allow 

steam or water into the exhaust. 

 

After maintenance 

»  Replace all protective mantles and other dismantled components. 
 

Repairs 

»  Repairs may only be carried out by qualified and authorized persons (see section 1.2). 

Always consult the service manual before carrying out any repairs. 

»  If the vehicle is defective, place a warning on the steering wheel and remove the key from 

the ignition. 

2.6.

 

Safety guidelines for transport 

Loading the vehicle for transportation 

»  Only loading platforms that are able to support the load and are sufficiently stable may be 

used.  The ramp gradient must be less than the maximum climbing capability of the 
vehicle (15%). 

»  Prevent the vehicle from overturning or sliding off during loading. 
»  Protect the vehicle from rolling off, shifting or overturning on a transport vehicle. 
 

Towing the vehicle

 

See Chapter 8. 
 

Not observing the regulations above is considered gross negligence. Tennant 
N.V. can not be held liable for any damage if you do not observe the safety 
regulations and measures mentioned above. 

Содержание A60






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды