Tennant A60 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 69

Tennant A60 Скачать руководство пользователя страница 15

TENNANT A60

English 1064354 rev. 00

- 15 -

Driving up gradients

» Driving on gradients is not recommended.
However, if driving on gradients is unavoidable, observe the following regulations:

Drive carefully and slowly when working on gradients or uneven terrain!
Increased risk of overturning!

» Do not drive up any gradients that exceed the vehicle's maximum climbing capability

(15%).

» Always drive carefully and straight up or down when driving on gradients.
» Wet and loose surfaces on gradients reduce the vehicle's road-holding capability.

Behavior in traffic

»  Adapt speed and work to the surrounding conditions.
»  Turn on the lights in case of reduced visibility.
»  Maintain sufficient distance from low curbs and soft shoulders.

Parking the vehicle

» Park the vehicle on flat, firm surfaces wherever possible.
» Before leaving the cabin:

-

set all operating controls to neutral.

-

engage the hand brake,

-

switch off the engine and remove the ignition key.

» Do not jump from the vehicle. Make use of the steps and handles intended for this purpose

when getting off the vehicle.

» Beware of obstacles when leaving the vehicle.
» When parking or stopping on slopes, always engage the hand brake to prevent the vehicle

from rolling downhill.

Refueling

»  Do not inhale the fuel fumes. Risk of health complaints.
»  Always switch off the vehicle and the engine when refueling.
»  Do not refuel in enclosed areas.
»  No open fire and no smoking.
»  Avoid spilling fuel. Catch spilt fuel and prevent it from seeping into the ground.

2.5.

Safety guidelines for maintenance

Before carrying out maintenance

» Maintenance may only be carried out by qualified and authorized persons (see section

1.2). Keep unauthorized persons away from the vehicle.

»  Never carry out maintenance work while the vehicle is moving or the engine is running.
»  Park the vehicle on a flat, firm surface.
»  Remove the key from the ignition.

Working on the hydraulic systems

» The hydraulic system must always be completely switched off and depressurized before

any work can be carried out on it.

» Never check for leaks in the hydraulic system by hand or close leaks by hand.

«
...
13
14
15
16
17
...
»

Содержание A60






































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды