Tennant 235 Скачать руководство пользователя страница 75

Страница: 75 / 82

MAINTENANCE

3-39

235 MM166 (3--94)

6. Remove the retaining strip of the seal to be

replaced.

03369

HOPPER SEALS

A. Top Hopper Seal

B. Side Hopper Seal

7. Remove the existing seal or skirt.

8. Mount the new seal or skirt to the machine

with the retaining strip removed earlier.

9. Replace the side access doors if removed.

10. Raise the hopper, place the hopper support

bar in its storage position, and lower the

hopper.

HOPPER DUMP DOOR SEAL

The hopper dump door seal allows the hopper to

be high dumped without scattering debris. Check

the seal for damage after every 100 hours of

operation.

TO REPLACE HOPPER DUMP DOOR SEAL

1. Empty the debris hopper.

2. Raise the hopper.

3. Engage the hopper support bar.

WARNING: Falling Hopper. Engage

HopperSupport Bar. Read Manual.

4. Stop the engine and set the machine

parking brake.

FOR SAFETY: Before Leaving Or Servicing

Machine; Stop On Level Surface, Set Parking

Brake, Turn Off Machine And Remove Key.

5. Open the dump door.

6. Remove the seal retaining strip.

03384

HOPPER DUMP DOOR SEAL

A. Hopper

B. Dump Door Seal

7. Remove the seal.

8. Mount the new seal to the door with the

sponge core and retaining strip removed

earlier.

9. Raise the hopper, position the hopper

support bar in its storage position, and lower

the hopper.

Содержание 235



















































































Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды

Tennant 235, Руководство оператора

Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды