Tennant 235 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 82

background image

This manual is furnished with each new TENNANT Model 235. It provides necessary operating and preventive
maintenance instructions. Read this manual completely and understand the machine before operating or servicing
it.

This manual covers all machine variations and standard accessories. The tabbed instruction portion of the
manual consists of the Specification, Operation, Maintenance, and Appendix sections. The tabbed parts section
consists of the Standard Model Parts; LPG Parts; Options; Hydraulic Components; Engine Parts, Gasoline, LPG;
and Cross Reference sections.

All right side and left side references to the machine are determined by facing the direction of forward travel. All
hardware considered to be of a common nature or locally available has been omitted from the parts sections. Be
aware that this machine may contain metric hardware. Make sure you use equivalent hardware when
replacement becomes necessary.

This machine will provide excellent service. However, the best results will be obtained at minimum costs if:

D

The machine is operated with reasonable care.

D

The machine is maintained regularly -- per the maintenance instructions provided.

D

The machine is maintained with Tennant Company supplied or equivalent parts.

Parts and supplies may be ordered by phone or mail from any Tennant Company parts and service center,
distributor, or from any of the Tennant Company subsidiaries. Before ordering parts or supplies, be sure to have
your machine model number and serial number handy. Fill out the data block below for future reference. The
telephone numbers, telex numbers, mailing addresses, and locations of those outlets are listed in the Customer
Documents section of the manual.

MACHINE DATA

Please fill out at time of installation.

Machine Serial Number --

Engine Serial Number --

Sales Representative --

Customer Number --

Date of Installation --

Manual Number -- MM166

Revision: 10

Published: 8--95

Trademark Registered in:

Austria, Benelux, Denmark, England, France, Germany, Italy, Spain, Switzerland,

United States, Argentina, Australia, Canada, Japan, Mexico, Sweden, by TENNANT COMPANY, Minneapolis,
Minnesota, U.S.A.

Acknowledgments:

Technical information and/or illustrations supplied by Kolher Company, Engine Division.

Copyright 1986, 1987,1988, 1989, 1991, 1993, 1994, 1995 Tennant Company, Printed in U.S.A.

«
1
2
3
4
...
»

Содержание 235



















































































Отзывы:

Нет отзывов

Похожие инструкции для 235

Бренд: KANSAI SPECIAL Страницы: 21

Бренд: Janome Страницы: 59

Бренд: Janome Страницы: 42

Бренд: Panasonic Страницы: 8

Бренд: Baby Lock Страницы: 76

Бренд: U.S. Products Страницы: 12

Бренд: Duerkopp Adler Страницы: 70

Autopax PAX600H

Бренд: Quasar Страницы: 148

GBC StreamPunch Ultra

Бренд: ACCO Brands Страницы: 92

Бренд: afx light Страницы: 19

Бренд: Lavor Страницы: 10

Office Bridge IF-200

Бренд: Muratec Страницы: 41

Бренд: Nilfisk-Advance Страницы: 2

GUARDIANS OF THE GALAXY LE

Бренд: Stern Pinball Страницы: 58

Бренд: Tacony Страницы: 16

Бренд: Vax Страницы: 24

Бренд: Ricoh Страницы: 87

GraceHoop 2 2005

Бренд: Grace Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды