Tennant 235 Скачать руководство пользователя страница 27

Страница: 27 / 82

OPERATION

2-9

235 MM166 (5--91)

CIRCUIT BREAKERS

Circuit breakers are resetable circuit protection

devices designed to stop the flow of current in the

event of a circuit overload. Once tripped, circuit

breakers must be manually reset. If the overload

which caused the circuit breaker to trip is still

present in the circuit, the circuit breaker will

continue to stop current flow until the overload is

corrected.

The circuit breakers are located on the instrument

panel bracket under the seat support.

The following chart shows the various circuit

breakers and the electrical components they

protect.

PROTECTIVE

CIRCUIT

DEVICE

RATING

PROTECTED

CB--1

15 A

Controls

CB--2

10 A

Horn

CB--3

10 A

Filter Shaker

CB--4

10 A

Hopper Dump Door

CB--5

7 A

Hopper Dump Door,
Thermo Sentry

and

Air Flow Solenoids

CB--6

15 A

Lights

03491

CIRCUIT BREAKERS

A. Instrument Panel Bracket

B. Circuit Breakers

HOPPER SUPPORT BAR

The hopper support bar is located on the right

side lift arm. It holds the hopper in a raised

position to allow work to be done under the

hopper. Do not rely on the machine hydraulic

system to keep the hopper raised.

WARNING: Raised Hopper May Fall.

Engage Hopper Support Bar.

Содержание 235



















































































Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды

Tennant 235, Руководство оператора

Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды