Tennant 235 Скачать руководство пользователя страница 3

Страница: 3 / 82

ABOUT THIS MANUAL

235 MM166 (5--91)

ABOUT THIS MANUAL

The machine manual that you received with your

TENNANT machine contains valuable information

about the operation and maintenance, and

numerous sections filled with TENNANT part

numbers for the repair of the machine. Please

read through this section titled

ABOUT THIS

MANUAL

to become familiar with the contents of

the machine manual, making the information you

are looking for easier to find.

The machine manual consists of several sections

of reference information, and the remainder

contain part number information for ordering

repair parts for the machine. Each section has a

shaded bar at the top of the page with the name

of that section. Just as this section has the title

ABOUT THIS MANUAL on the top of each page.

This way you can tell which section you are in at

all times.

REFERENCE SECTIONS

The reference information sections of the manual

are; General Information, Specifications,

Operation, Maintenance, and Appendix.

GENERAL INFORMATION

-- The General

Information section of the manual contains the

safety precautions, the location of the safety

labels on the machine, and a table of contents of

the entire manual. The Safety Precautions are an

overview of the safety measures to be observed

when operating and maintaining your machine.

The location of the safety labels show the

mounting location of the safety labels for use in

the replacement of the labels. The table of

contents in this section is a list of all the table of

contents that appear in the front of each section in

the manual. This can be used for easy reference

to locate information in a particular section of the

manual.

SPECIFICATIONS

-- The Specifications section of

the manual contains machine specification

information useful in the operation and

maintenance of the machine. This section gives

you specification information on the engine,

electric motors, brake system, hydraulics, fluid

capacities, and machine weight to mention a few.

The section also has a illustration of the top and

side view of the machine with the height and width

dimensions displayed.

OPERATION

-- The Operation section of the

manual contains information needed to operate

the machine. This section will list the controls and

instruments on the machine, overview the

machine operation, and tell you how to transport

and store the machine.

MAINTENANCE

-- The Maintenance section

contains information on the suggested

maintenance procedures and adjustments to keep

your machine in top operating condition. The

section includes a Maintenance Chart listing the

maintenance schedule and the areas of the

machine to be addressed. Each subject of

maintenance is covered in more detail in such

areas as Lubrication, Hydraulics, Engine, and

Electrical System.

APPENDIX

-- The Appendix contains hardware

and hydraulic information. Standard hardware

torques and identification information is included,

plus hydraulic torques if your machine is

hydraulically controlled.

PART SECTIONS

The remaining sections of the manual contain part

number information for ordering repair parts for

your machine. The manual contains part number

information on every type of machine model

available in the model size of your particular

machine. Therefore there will be part number

information in your manual you will not need to

refer to when wanting to place an order.

The main thing you need to know about your

machine is what type of model is it. Is the

machine powered by an engine or batteries? If the

machine has an engine, is it fueled from gasoline,

LPG, or diesel? If it is a mid-sized or larger

sweeper, is it multi-level or low dump? For the

scrubbers, is it SRS

or standard. Determining

this information about your machine will help

guide you through the separate parts sections to

find the repair part you need.

Содержание 235



















































































Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды

Tennant 235, Руководство оператора

Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды