Tennant 235 Скачать руководство пользователя страница 71

Страница: 71 / 82

MAINTENANCE

3-35

235 MM166 (3--94)

NOTE: If no chalk or other material is available,

allow the brushes to spin on the floor for two

minutes.

4. Observe the brush pattern made. The

pattern should be of equal width across the

length of the pattern.

00582

NORMAL MAIN BRUSH PATTERN

A. Main Brush Pattern

B. 2 to 2.5 in (51 to 54 mm) for

machines serial number 002594 and

above

For machines serial number 002594 and

above, and machines with the Brush Limiter

Kit installed, the brush pattern width should

be 2 to 2.5 in (51 to 54 mm). The brush

pattern width can be adjusted by loosening

and moving the brush limiter nut.

03487

BRUSH LIMITER NUT (For machines serial

number 002594 and above)

A. Brush Limiter Nut

B. Main Brush Lever Slot

To decrease the width of the brush pattern,

move the limiter nut forward and tighten the

nut. To increase the brush pattern width,

move the limiter nut back and tighten the

nut.

If the main brush pattern is tapered, wider

on one side by 0.50 in (15 mm) or more than

the other side, perform the following leveling

procedure:

00601

TAPERED MAIN BRUSH PATTERN

A. Park the machine on a level surface.

B. Stop the engine and set the machine

parking brake.

FOR SAFETY: Before Leaving Or Servicing

Machine; Stop On Level Surface, Set Parking

Brake, Turn Off Machine And Remove Key.

C. Lower the main brush.

D. Remove the right side access door.

E. Remove the main brush.

F. Reinstall the idler arm.

G. Loosen the cross shaft bearing flange

bolts.

03550

CROSS SHAFT BEARING FLANGE

A. Flange

B. Bolts

C. Cross Shaft

Содержание 235



















































































Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды

Tennant 235, Руководство оператора

Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды