Tennant 235 Скачать руководство пользователя страница 54

Страница: 54 / 82

MAINTENANCE

235 MM166 (5--91)

3-18

The initial setting of the main fuel needle valve, if

it is present, is made by lightly turning it all the

way in, then turning it out two and three-quarter

turns. The fuel tank should be approximately

one-half full and with the engine running at

approximately 2200 RPM. Final adjustment is

made with the engine warm. Turn the main fuel

adjusting needle valve out until the engine begins

to lose speed (rich). Note the position of the

needle. Then turn the needle in. The engine

speed may increase, then it will decrease as the

needle is turned in (lean). Note the position of the

needle. Set the needle half way between the rich

and lean positions.

03496

CARBURETOR ADJUSTMENTS

A. Idle Needle Valve

B. Main Fuel Needle Valve

FUEL SYSTEM -- LPG

LPG FUEL SYSTEM
The LPG fuel system is made up of six

components which are: the LPG fuel tank,

pressure relief valve, fuel filter lock,

vaporizer-regulator, secondary regulator, and the

carburetor.

Liquid LPG fuel flows from the LPG tank, under its

own pressure, to the pressure relief valve. This

valve is normally closed, preventing LPG fuel from

escaping into the atmosphere. The valve opens to

relieve pressure if the fuel pressure exceeds

system limits. From the pressure relief valve, the

LPG fuel is piped to the fuel filter lock. The fuel

filter lock filters unwanted tank scale and deposits

out of the LPG fuel. The fuel filter lock also stops

the flow of LPG fuel when the engine is not

operating. The oil pressure switch controls the

fuel filter lock. When the engine oil pressure is 4

psi (30 kPa) or greater, the oil pressure switch

permits an electrical current to open the fuel filter

lock which allows LPG fuel to flow on to the

vaporizer, then the regulator. The oil pressure

switch is bypassed when the engine is being

started, allowing LPG fuel to flow.

The vaporizer converts the LPG fuel into a

gaseous LPG fuel. Within the vaporizer, the

gaseous LPG fuel is sent to the primary regulator.

The primary regulator section reduces the

pressure of the LPG fuel. From the primary

regulator section of the vaporizer, the LPG fuel is

sent to the secondary regulator. The secondary

regulator reduces the LPG fuel pressure to the

level required by the carburetor. Then the fuel is

sent to the carburetor where it is finally metered

into the air flow which is sent to the engine

combustion chamber.

04232

LPG FUEL SYSTEM

A. Carburetor

B. Secondary Regulator

C. Vaporizer-Regulator

D. Fuel Filter Lock

E. Pressure Relief Valve

F. Tank Service Valve

G. LPG Fuel Tank

H. Oil Pressure Switch

Содержание 235



















































































Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды

Tennant 235, Руководство оператора

Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды