Tennant 235 Скачать руководство пользователя страница 81

Страница: 81 / 82

APPENDIX

4-3

235 MM166 (5--91)

HARDWARE INFORMATION

The following charts state standard plated

hardware tightening ranges for normal assembly

applications. Decrease the specified torque by

20% when using a thread lubricant. Do not

substitute lower grade hardware for higher grade

hardware. If higher grade hardware than specified

is substituted, tighten only to the specified

hardware torque value to avoid damaging the

threads of the part being threaded into, as when

threading into speed nuts or weldments.

STANDARD BOLT TORQUE CHART

Thread

SAE Grade 5

SAE Grade 8

Size

Torque ft lb (Nm)

0.25 in

7--10 (9--14)

10--13 (14--38)

0.31 in

15--20 (20--27)

20--26 (27--35)

0.38 in

27--35 (37--47)

36--47 (49--64)

0.44 in

43--56 (58--76)

53--76 (72--103)

0.50 in

65--85 (88--115)

89--116 (121--157)

0.62 in

130--170 (176--231)

117--265 (159--359)

0.75 in

215--280 (291--380)

313--407 (424--552)

1.00 in

500--650 (678--881)

757--984 (1026--1334)

NOTE: Decrease torque by 20% when using a

thread lubricant.

METRIC BOLT TORQUE CHART

Thread

Class 8.8

Class 10.9

Size

Torque ft lb (Nm)

2 (3)

3 (4)

4 (5)

6 (8)

7 (9)

10 (14)

18 (24)

25 (34)

M10

32 (43)

47 (64)

M12

58 (79)

83 (112)

M14

94 (127)

133 (180)

M16

144 (195)

196 (265)

M20

260 (352)

336 (455)

M24

470 (637)

664 (900)

NOTE: Decrease torque by 20% when using a

thread lubricant.

Exceptions to the above chart:

Main brush drive plug nut -- 30 ft lb (40 Nm)

then tighten to next slot.

Brake unit to hub sockethead screw --

9 to 12 ft lb (12 to 16 Nm) with Locktite 242

blue.

Front wheel nut -- 10 to 12 ft lb (14 to

16 Nm) while turning wheel, tighten to spec,

then backoff, retighten by hand till snug,

then turn to next slot.

Rear hub to shaft nut -- 175 ft lb (240 Nm)

then to next slot.

Damper solenoid nut -- 20 to 23 in lb

(2.5 to 3 Nm).

BOLT IDENTIFICATION

Identification

Specification

Grade Marking

and Grade

SAE--Grade 5

SAE--Grade 8

ISO--Grade 8.8

ISO--Grade 10.9

01395

THREAD SEALANT AND LOCKING

COMPOUNDS

Thread sealants and locking compounds may be

used on this machine. They include the following:

Locktite 515 sealant -- gasket forming

material. TENNANT Part No. 75567,15 oz

(440 ml) cartridge.

Locktite 242 blue -- medium strength thread

locking compound. TENNANT Part No.

32676, 0.5 ml tube.

Locktite 271 red -- high strength thread

locking compound. TENNANT Part No.

19857, 0.5 ml tube.

Содержание 235



















































































Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды

Tennant 235, Руководство оператора

Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды