Tennant 235 Скачать руководство пользователя страница 33

Страница: 33 / 82

OPERATION

2-15

235 MM166 (5--91)

TRANSPORTING MACHINE

PUSHING OR TOWING MACHINE

The machine may be slowly pushed from the front

or rear, pushing on the bumper or the machine

frame.

The machine may be slowly towed from the front.

Use care when attaching towing cables or chains

to avoid damaging the machine.

MACHINE JACKING

The machine may be jacked up for service at the

designated locations. Use a jack of adequate

capacity and good working condition. Always stop

the machine on a flat, level surface and block the

tires before jacking the machine up.

The front jacking locations are on the flat bottom

edge of the machine frame next to the front tires.

The rear jacking location is the middle flat bottom

edge of the rear bumper.

TO JACK UP MACHINE

1. Empty and lower the debris hopper.

2. Stop the engine and set the machine

parking brake.

FOR SAFETY: Before Leaving Or Servicing

Machine; Stop On Level Surface, Set Parking

Brake, Turn Off Machine And Remove Key.

3. Block the tires, which are not being jacked

up, in order to secure the machine position.

FOR SAFETY: When Servicing Machine, Block

Machine Tires Before Jacking Machine Up.

4. Use a jack of adequate capacity to raise the

machine. Jack up the machine only at the

designated locations.

FOR SAFETY: When Servicing Machine, Use

Hoist Or Jack Of Adequate Capacity To Lift

Machine, Jack Machine Up At Designated

Locations Only. Block Machine Up With Jack

Stands.

03372

FRONT JACKING LOCATION

A. Jacking Location

03373

REAR JACKING LOCATION

A. Jacking Location

5. Block machine up with jack stands or similar

devices in the designated locations to

secure the machine.

FOR SAFETY: When Servicing Machine, Jack

Machine Up At Designated Locations Only.

Block Machine Up With Jack Stands.

Содержание 235



















































































Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды

Tennant 235, Руководство оператора

Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды