Tennant 235 Скачать руководство пользователя страница 53

Страница: 53 / 82

MAINTENANCE

3-17

235 MM166 (5--91)

5. Remove the foam precleaner.

03495

REMOVING ENGINE AIR FILTER

A. Foam Precleaner

B. Dry Cartridge-Type Air Filter

6. Wash the foam precleaner in liquid

detergent and water.

7. Squeeze it dry in a cloth.

8. Remove the dry cartridge-type filter nut and

cup.

9. Gently remove the dry cartridge-type air

filter.

10. Clean or discard the dry cartridge-type air

filter.

11. Clean the interior of the air cleaner housing

with a damp cloth. Clean the element

sealing surfaces.

12. Position the cleaned or new, dry

cartridge-type air filter on the engine.

13. Slide the air filter cup over the air filter stud.

14. Thread and tighten the nut onto the air filter

stud.

15. Oil the foam precleaner with 1 oz (30 cc) of

clean engine oil. Squeeze the precleaner to

distribute the oil evenly throughout the foam.

16. Slide the foam precleaner over the dry

cartridge-type filter.

17. Position the air filter cover over the air filter

assembly. Tighten the wing nut on the air

filter stud.

FUEL SYSTEM, GASOLINE

FUEL FILTER
An in-line fuel filter has been provided to filter the

fuel. The filter is located next to the fuel tank. The

system is also equipped with a fuel shutoff valve.

Replace the filter when necessary.

CARBURETOR
The carburetor idle speed should be checked and

adjusted after every 400 hours of operation. Early

machines had an idle and a main fuel valve. Later

machines only have an idle fuel valve.

The initial setting of the idle fuel needle valve is

made by lightly turning it all the way in, then

turning it out one-half turn. Final adjustment is

made with the engine running and warm.

Содержание 235



















































































Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды

Tennant 235, Руководство оператора

Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды