Tennant 235 Скачать руководство пользователя страница 57

Страница: 57 / 82

MAINTENANCE

3-21

235 MM166 (5--91)

FUEL FILTER LOCK
The fuel filter lock filters the LPG fuel. It also

stops the flow of LPG fuel to the engine when the

engine is not operating or when the engine oil

pressure is less than 4 psi (30 kPa).

Replace the filter pack with the filter pack

replacement kit if diminished gas flow indicates

the filter is clogged. A drain plug is provided for

purging the filter bowl. Clean out the bowl when

replacing the filter pack.

VAPORIZER-REGULATOR
nIf any malfunction is noted, completely

disassemble the vaporizer-regulator. Clean all of

the parts in alcohol. Inspect all of the parts and

replace where needed. Carefully reassemble the

vaporizer-regulator with the seal repair kit. Check

for proper operation.

CARBURETOR
If any malfunction is noted, completely

disassemble the carburetor. Clean all of the parts

in alcohol.

Inspect all of the parts and replace when needed.

Carefully reassemble the carburetor with the seal

repair kit.

OIL PRESSURE SWITCH
The engine oil pressure switch requires no regular

maintenance. Never bypass the oil pressure

switch as this is a safety feature which prevents

LPG fuel from flowing when the engine is not

operating properly.

LPG FUEL TROUBLESHOOTING

Problem

Cause

Remedy

Engine will not start

Out of fuel

Replace fuel tank with full one

Engine will not start

Service valve opened too quickly

-- engaging safety valve

Close valve and reopen slowly

Plugged fuel filter

Replace filter

Kinked or restricted fuel line

Straighten or replace fuel line

Engine out of tune

Tune-up engine

Oil pressure switch failure

Replace oil pressure switch

Fuel lock valve failure

Repair or replace fuel filter lock

Vaporizer-regulator failure

Repair or replace vaporizer-regu-

lator

Engine runs unevenly or lacks

power

Wrong type of fuel tank

Replace with either vapor or liquid

withdrawal tank for proper system

power

Plugged fuel filter

Replace filter

Kinked or restricted fuel line

Straighten or replace fuel line

Engine out of tune

Tune-up engine

Restricted air filter

Clean or replace air filter element

Vaporizer-regulator maladjusted

Adjust vaporizer-regulator

Содержание 235



















































































Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды

Tennant 235, Руководство оператора

Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды