Tempco TEC-2500 Скачать руководство пользователя страница 95

Страница: 95 / 108

Chapter 7 Error Codes and Troubleshooting

This procedure requires access to the circuitry of a unit under live power. Accidental contact with line voltage is

possible. Only qualified personnel should perform these procedures. Potentially lethal voltages are present.

Troubleshooting procedures:

1. If an error message is displayed, refer to table 7.1 to see what caused it and what action to take to correct the

problem.

2. Check each point listed below. Experience has proven that many control problems are caused by a defective

instrument.
• Line wires are improperly connected

• No voltage between line terminals

• Incorrect voltage between line terminals

• Connections to terminals are open, missing, or loose

• Thermocouple is open at tip

• Thermocouple lead is broken

• Shorted thermocouple leads

• Short across terminals

• Open or shorted heater circuit

• Open coil in external contactor

• Burned out line fuses

• Burned out relay inside control

• Defective solid-state relays

• Defective line switches

• Burned out contactor

• Defective circuit breakers

3. If the points listed on the above chart have been checked and the controller still does not function properly, it is

recommended that the instrument be returned to the factory for inspection. Do not attempt to make repairs without a

qualified engineer and proper technical information, as damage may result. It is also recommended to use adequate

packing materials to prevent damage during transportation.

4. Dismantle the controller according to figure 7.1. Refer to table 7.2 for some probable causes and actions.

Содержание TEC-2500













































































































Результаты поиска

Содержание TEC-2500

Отзывы:

Похожие инструкции для TEC-2500

Бренды по названию

Популярные бренды

Tempco TEC-2500, Инструкция по эксплуатации

Результаты поиска

Содержание TEC-2500

Отзывы:

Похожие инструкции для TEC-2500

Бренды по названию

Популярные бренды