Tempco TEC-2500 Скачать руководство пользователя страница 92

Страница: 92 / 108

Step 4.

Set the DIP switch for voltage input. Press the scroll key until the display shows .

Send a 10V signal to terminals 10 and 11 with the correct polarity. Press the scroll key for at

least 3 seconds. The display will blink for a moment until a new value is obtained. If the

display didn't blink or if the obtained value is equal to -199.9 or 199.9, then calibration failed.

• Perform both steps 5 and 6 to calibrate RTD function (if required) for input 1.

Step 5.

Set the DIP switch for RTD input. Press the scroll key until the display shows . Send

a 100 ohms signal to terminals 8, 9, and 10 using to the connection shown below:

Press the scroll key for at least 3 seconds. The display will blink for a moment; if it does not,

calibration failed.

Step 6.

Press the scroll key and the display will show . Change the ohm's value to 300 ohms.

Press the scroll key for at least 3 seconds. The display will blink for a moment while values

are obtained for SR1 and REF1 (last step). If the display didn't blink or if any value obtained

for SR1 or REF1 is equal to -199.9 or 199.9, then calibration failed.

• Perform step 7 to calibrate mA function (if required) for input 1.

Step 7.

Set the DIP switch for mA input. Press the scroll key until the display shows . Send a

20mA signal to terminals 9 and 10 with the correct polarity. Press the scroll key for at least 3

seconds. The display will blink for a moment until a new value is obtained. If the display

didn't blink or if the obtained value is equal to -199.9 or 199.9, then calibration failed.

• Perform step 8 to calibrate voltage as well as CT function (if required) for input 2.

Step 8.

Press the scroll key until the display shows . Send a 10V signal to terminals 10 and

11 with the correct polarity. Press the scroll key for at least 3 seconds. The display will blink

for a moment until a new value is obtained. If the display didn't blink or if the obtained value

is equal to -199.9 or 199.9, then calibration failed.

• Perform step 9 to calibrate offset of cold junction compensation, if required. Set the DIP

switch for T/C input.

• Perform step 10 to calibrate the gain of cold junction compensation if required. If a test

chamber for calibration is not available, perform step 10N to use a nominal value for the cold

junction gain.

1 2 3 4

DIP Switch Position

RTD Input

Содержание TEC-2500













































































































Результаты поиска

Содержание TEC-2500

Отзывы:

Похожие инструкции для TEC-2500

Бренды по названию

Популярные бренды

Tempco TEC-2500, Инструкция по эксплуатации

Результаты поиска

Содержание TEC-2500

Отзывы:

Похожие инструкции для TEC-2500

Бренды по названию

Популярные бренды