Tempco TEC-2500 Скачать руководство пользователя страница 61

Страница: 61 / 108

3–24 Display Mode

Operation

Press several times until (display) appears on the display. Then press to enter

display mode. You can select more parameters to view by pressing or pressing in

reverse sequence. The system mode of the controller and its operation will remain unchanged.

When the controller enters display mode the display will alternate between showing the display

parameter and the parameter value.

PVHI/PVLO

show the historical extreme (maximum or minimum) values of the process on the

upper display. The historical extreme values are saved in a nonvolatile memory even when it is

unpowered. Press for at least 6 seconds to reset both the historical values PVHI and PVLO

and begin to record new peak process values.

shows the percentage control value for output 1, while shows the percentage

control value for output 2.

shows the difference value between process and set point (i.e., PV-SV). This value is used

to control output 1 and output 2.

PV1

shows the process value of input 1.

PV2

shows the process value of input 2.

shows the current proportional band value used for control.

shows the current integral time used for control.

shows the current derivative time used for control. Since the controller is performing

FUZZY

control, the values of PB, TI, and TD may change from time to time.

CJCT

shows the temperature at the cold junction, measured in °C independent of the unit

used.

PVR

Shows the changing rate of the process in °C (or °F or PU) per minute. It may be

negative if the process is going down.

PVRH/PVRL

The maximum and minimum changing rate of the process since power up, as

measured in °C (or °F or PU) per minute. PVRH is a positive value while PVRL is a negative

value.

NOTE

The controller will never revert to its PV/SV display from display mode

unless you press the keys.

PVHI
PVLO
MV1
MV2
DV
PV1
PV2
PB
TI
TD
CJCT
PVR
PVRH
PVRL

Содержание TEC-2500













































































































Результаты поиска

Содержание TEC-2500

Отзывы:

Похожие инструкции для TEC-2500

Бренды по названию

Популярные бренды

Tempco TEC-2500, Инструкция по эксплуатации

Результаты поиска

Содержание TEC-2500

Отзывы:

Похожие инструкции для TEC-2500

Бренды по названию

Популярные бренды