Tempco TEC-2500 Скачать руководство пользователя страница 49

Страница: 49 / 108

3–13 Loop Break Alarm

A1FN selects LB if alarm 1 is required to act as a loop break alarm. Similarly, if

alarm 2 is required to act as a loop break alarm, then set OUT2 to AL2 and

A1FN to LB. TIME, A1SP, A1DV, and A1HY are hidden if alarm 1 is configured

as a loop break alarm. Similarly, TIME, A2SP, A2DV, and A2HY are hidden if

alarm 2 is configured as a loop break alarm.
One of four kinds of alarm modes can be selected for alarm 1 and alarm 2.

These are: normal alarm, latching alarm, holding alarm and latching/holding

alarm. However, the holding mode and latching/holding mode are not

recommended for loop break alarm since loop break alarm will not perform the

holding function even if it is set for holding or latching/holding mode. See

section 3-9 for descriptions of these alarm modes.
Loop break conditions are detected during a time interval of 2TI1 (double the

integral time, but 120 seconds maximum). Hence the loop break alarm doesn't

respond as quickly as it occurs. If the process value doesn't increase (or

decrease) while the control variable MV1 has reached its maximum (or

minimum) value within the detecting time interval, a loop break alarm (if

configured) will be activated.

Loop break alarm (if configured) occurs when any following conditions happen:

1. Input sensor is disconnected (or broken).

2. Input sensor is shorted.

3. Input sensor is defective.

4. Input sensor is installed outside (isolated from) the process.

5. Controller fails (A-D converter damaged).

6. Heater (or chiller, valve, pump, motor etc.) breaks or fails or is uninstalled.

7. Switching device (used to drive heater) is open or shorted.

Loop break alarm 1

Setup: A1FN=LB

A1MD=NORM, LTCH

Loop break alarm 2

Setup: OUT2=AL2

A2FN=LB

A2MD=NORM, LTCH

Содержание TEC-2500













































































































Результаты поиска

Содержание TEC-2500

Отзывы:

Похожие инструкции для TEC-2500

Бренды по названию

Популярные бренды

Tempco TEC-2500, Инструкция по эксплуатации

Результаты поиска

Содержание TEC-2500

Отзывы:

Похожие инструкции для TEC-2500

Бренды по названию

Популярные бренды